REED Bevel Boss Instructions

READ BEFORE USE:
1. Check the bevel length/setting of the router bit.
2. Start the grinder BEFORE touching the router
bit to the pipe. It needs to be at full RPM
before you touch the pipe.
3. New users should make a practice bevel or
two before working on the jobsite pipe.
REED Bevel Boss Cordless Pipe Bevelers (CPB) are designed
®
for use with a cordless die grinder to bevel the outside diameter
and/or inside diameter of plastic pipe. REED Bevel Boss®
Beveler Adapters Heads fit ONLY DeWalt®, Milwaukee® or
Bosch® cordless die grinders – match the Adapter Head to
the right die grinder. Assembly instructions are provided in this
document.
ASSEMBLY DIAGRAM 1
REED CPBDK kit is complete with beveler attachment with
exterior shroud, Router Bit RBIT1, die grinder, DeWalt® battery
SHROUD
and charger in a storage case. The CPBDBT base tool with
beveler attachment and die grinder requires a router bit and
GUIDE PLATE
DeWalt battery. Refer to these instructions for assembly of bit
®
into beveler. Many users already own the battery and are able to
use it on this REED tool.
NOTE: Internal shroud CPBIDS #94644 must used for
beveling the inside diameters and is available as an accessory.
PERSONAL SAFETY
ADJUSTING KNOB
1. Stay alert, watch what you are doing and use common
MUST BE LOCATED
90° FROM SWITCH
sense when operating a power tool. Do not use tool while
AS SHOWN
tired or under the influence of drugs, alcohol, or medication.
A moment of inattention while operating power tools may
result in serious personal injury.
MILWAUKEE
2. Dress properly. Do not wear loose clothing or jewelry. GRINDER
Contain long hair. Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewelry, or long hair can
be caught in moving parts.
3. Always wear eye protection.
OPERATING INSTRUCTIONS:
This tool is to be used on plastic pipe only. To adjust depth of
chamfer, loosen the adjusting knob and slide the guide plate up
or down until the required amount of the router bit is exposed
above the guide plate and tighten the adjusting knob. To the
left side of the Adjusting Knob there are four engraved lines on
Adapter with 1/8" increments. When using the RBIT1 bit with
the Adjusting Ring all the way to the bottom, the beveler will cut
a 5/8" long bevel. By lining up the bottom of the Adjusting Ring
with the engraved line, the length of the bevel is reduced by 1/8"
for each line.
VIDEO
TRAINING
Bevel Boss
CPBDK, CPBDBT, CPBDKE, CPBDADP, CPBMADP, CPBMADP29, CPBBADP
Adapting to DeWalt
GUIDE PLATE
SHOULD BE FLUSH
WITH BOTTOM OF
ROUTER BIT
CLAMP SCREW
ADAPTER HEAD
FITS MILWAUKEE ®
1425 West 8th Street Erie, PA 16502 USA
Cordless Pipe Beveler Instructions
®
, Milwaukee
®
Applies To: 04658, 04659, 04666, 04648, 04649, 04671, 04646
If the grinder is capable of multiple speeds, set the
grinder to the fastest setting. Turn on grinder and place
guide plate flat against the end of pipe. Slowly bring the
router bit against edge of pipe until the bearing at the end
of the bit is contacting the pipe. Slowly rotate the beveler
counterclockwise for an OD bevel and clockwise for an
ID bevel, being sure to keep the bearing in contact with pipe. A
second quick pass around the pipe may be needed if the bevel
is not smooth. An uneven bevel can happen if the guide plate
APPROXIMATE
is not kept perpendicular to the pipe and the bearing on the
router bit is not kept against the pipe.
OPERATING INSTRUCTIONS RBIT2 (1" BIT) ONLY:
The RBIT2 (1" bit) removes a large amount of material.Therefore,
it is STRONGLY RECOMMENDED when cutting a ¾" to 1"
depth bevel to make two passes around the pipe, removing
half of the material with each pass. For the first pass set the
Adjusting Ring so it lines up with the engraved line to the right of
the Adjusting Screw and make the first pass around the pipe. To
complete the bevel, readjust the Adjusting Ring to remove the
remainder of the material.
OPERATING DIAGRAM
4 REFERENCE LINES
1/8" INCREMENTS
FOR ADJUSTING
THE BEVEL SIZE
CPBDADP fits DeWalt
Lithium-Ion Cordless Brushless Variable Speed Die Grinder
CPBMADP fits Milwaukee
M18 FUEL™ 18V Lithium-Ion Brushless Die Grinder
CPBMADP29 fits Milwaukee
2984-20 M18 FUEL ™ Die Grinders
®
DeWalt and Milwaukee
REED MANUFACTURING
Phone: 800-666-3691 or +1 814-452-3691
Fax: +1 814-455-1697 reedsales@reedmfgco.com
www.reedmfgco.com
and Bosch
®
ASSEMBLY DIAGRAM 2
5/32"
OPERATING DIAGRAM
RBIT2
RECOMMENDED:
SET HEIGHT TO THIS LINE
FOR REMOVING HALF THE
1/8"
MATERIAL FOR FIRST PASS
ON LARGER BEVEL
WHEN USING RBIT2
®
model DCG426B 20V MAX XR
®
models 2784-20 and 2784-22
®
models 2939-20 and
®
are registered trademarks that are not associated with Reed Mfg.
Die Grinders
®
RBIT1
LOCATE ROUTER BIT SO
THE UNFINISHED AREA ON
THE SHAFT IS JUST ABOVE
TOP OF COLLET
COLLET
1
0523-54654