Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
Frame
Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: 75601F
Wrenches: 18mm, 19mm
Drill Bits: None
Existing flange
Nuts
Hitch bracket
Bumper mounting bracket
Typical both sides
1
Qty. (2)
Hex Bolt – M12 x 1.75 x 120mm CL8.8
2
Qty. (2)
Spacer – 7/16" x 1" x 2"
Note: Existing bumper mounting bolts in vehicle frame, 3 each side, may come from the factory pointing inboard. For hitch installation,
bolts MUST be pointing outboard with the head of the bolt against the bumper mounting bracket. Do not remove all bolts at
once as this will cause the bumper to fall. Instead, bolts must be turned around one at a time to prevent bumper from falling.
1.
Remove all nuts from existing bumper mounting bolts, 3 per side. Do not remove bolts yet.
2.
If bumper mounting bolts are pointing inboard, turn bolts, one at a time so that bolts are pointing outboard. Leave flush with
outboard side of frame rails. This will support bumper mounting brackets and allow hitch to be installed on outboard side of
frame. If bolts are already pointing outboard, pull bolts out to just flush with outboard side of frame.
3.
Raise hitch into position. Push bumper mounting bolts the rest of the way thru hitch brackets. Reinstall flange nuts removed in
step 1.
4.
Install the rest of the bolts as shown above.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2007 Cequent Towing Products
Installation Instructions
Dodge Sprinter with factory step bumper
Freightliner Sprinter with factory step bumper
Step
Bumper
43
Tighten all M12 fasteners with torque wrench to 68 Lb.-Ft. (92 N*M)
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
Hitch type
Weight Distributing
Weight Carrying
Ball Mount
Wiring Access Location: SUV1, SUV2
Warning: To prevent bumper from falling,
Do NOT remove all existing
Bumper Mounting bolts at once.
12
Existing Flange Bolts
Must be Pointing
Outboard
3
Qty. (2)
Lock Washer ½"
4
Qty. (2)
Hex Nut M12 x 1.75
Sheet 1 of 3
75601N
Part Numbers:
75601
44591
87456
Max Gross
Max Tongue
Trailer WT (LB)
WT (LB)
7500 (3405 Kg)
750 (341 Kg)
5000 (2270 Kg)
500 (227 Kg)
12
34
8-10-07
Rev. A
Form: F205 Rev A 5-6-05
Existing
Flange
Nuts
Publicité
Manuels Connexes pour Cequent Towing Products 75601
Sommaire des Matières pour Cequent Towing Products 75601
- Page 1 This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. Sheet 1 of 3 75601N 8-10-07 Rev. A 2007 Cequent Towing Products Form: F205 Rev A 5-6-05...
- Page 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. Feuille 2 de 3 75601N 8-10-07 Rev. A 2007 Cequent Towing Products Form: F205 Rev A 5-6-05...
- Page 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulación V-5 y SAE J684. Sheet 3 of 3 75601N 8-10-07 Rev. A 2007 Cequent Towing Products Form: F205 Rev A 5-6-05...