Taymor ASTRAL 06-8722 Instructions D'installation

INSTALLATION INSTRUCTIONS
ASTRAL 06-8722 / 06-8722CBLK
SINGLE HANDLE KITCHEN FAUCET
THIS FAUCET MEETS OR EXCEEDS THE FOLLOWING STANDARDS:
cUPC, ASME A112.18.1, NSF-61 AND LOW LEAD COMPLIANT
THANK YOU FOR PURCHASING THIS TAYMOR PRODUCT. ALL TAYMOR PRODUCTS ARE CAREFULLY
ENGINEERED AND FACTORY TESTED TO PROVIDE LONG TROUBLE-FREE USE UNDER NORMAL CONDITIONS.
HAVE BASIC TOOLS READY
1
RECOMMENDED TOOLS:
Teflon tape Screwdrivers Adjustable Flashlight
wrench and
pipe wrench
WARNING: READ ALL the instructions completely before beginning.
READ ALL warnings, care and maintenance information.
Taymor recommends calling a professional if you are uncertain about installing this product!
This product should be installed in accordance with all local and provincial plumbing and building codes.
Need Help? Please call our toll-free Customer Support line at
(WEST) 1-800-267-4774 (EAST ) 1-800-387-7064 for additional assistance or service.
TURN OFF THE MAIN WATER SUPPLY
2
Locate water supply inlets and shut off water supply valves. These are usually found under
the sink.
TURN OFF
3 FAUCET INSTALLATION
1a) With Escutcheon. Apply a bead of plumber's putty or silicone caulk around the sink openings. Install the
gasket over the three holes in your sink.
1b) Install faucet hoses through the hole of the sink. Centre the faucet body. Make sure that handle is properly
aligned to sink.
With Flange. Place flange #1 on the bottom of faucet. Place faucet through mounting hole in sink.
2)
3) From underneath the sink, secure the faucet with washer #2 and nut #3. Do not over tighten.
Don't use plumber's putty on cultured marble or other composite sinks.
Putty will discolour the sink.
1a
2
1
WITH OPTIONAL ESCUTCHEON
Your installation may require new supply
lines. (Supply lines are not included.)
Safety goggles
Torque wrench Plumber's putty
TURN OFF
1b
3
2
3
ATTACH THE HOT AND COLD SUPPLY LINES
4
Apply teflon tape onto threaded ends of faucet inlets. Connect water supply lines to faucet inlets.
Hot water supply lines go into left inlet. Cold water supply lines go into right inlet.
(Supply lines are not included.)
FOR PLASTIC AND BRAIDED
STAINLESS STEEL SUPPLY TUBES
THESE SUPPLY TUBES HAVE INTEGRAL NUTS.
SCREW THE NUT ONTO THE FAUCET INLET.
TORQUE
22 – 30 FT/LBS.
FLUSHING & AERATOR CLEANING
5
Remove the aerator by turning it counterclockwise. Remove the internal parts of the aerator by push-
ing them out with your fingers. Remove any debris. Turn on hot and cold water supplies. Turn faucet
handle all the way on and run water through the spout for about a minute to remove debris. While
Silicone caulk
water is running check all connections for leaks. Reassemble the aerator and screw it back into the
spout, hand tighten.
EXPLODED DIAGRAM FOR REFERENCE
6
MAINTENANCE Your new faucet is designed for years of trouble-free performance. Keep it looking
new by cleaning it periodically with a soft cloth. Avoid abrasive cleaners, steel wool and harsh
chemicals as these will dull the finish and void your warranty.
GASKET
AERATOR
AERATOR SHELL
2 - AERATOR ASSEMBLY
21 - O-RING
CUSTOMER SERVICE WEST 1-800-267-4774 | EAST 1-800-387-7064 | taymor.com
FOR 3/8" O.D. BALL-NOSE SUPPLY TUBES
IF THE SUPPLY TUBE END HAS A BULBOUS SHAPE,
USE THE SUPPLIED COUPLING NUTS.
TORQUE
22 – 30 FT/LBS.
1 - SPOUT
3 - WASHER
4 - SPOUT NUT
5 - CLIP
6 - O-RING
7 - SLEEVE
8 - O-RING
17 - INDEX
9 - BODY
16 - HANDLE
10 - CARTRIDGE
18 - SET SCREW
15 - BOLT
11 - BONNET
12 - CAP
14 - HANDLE SEAT
19 - SPOUT FLANGE
13 - SCREW
20 - WASHER
22 - BOLT
23 - WASHER
24 - HOSE
27 - ESCUTCHEON
26 - MOUNTING NUT
25 - COUPLING NUT
28 - BASE PLATE
® REGISTERED TRADEMARK OF TAYMOR INDUSTRIES LTD.