Ortech DISC3-3K Instructions D'installation

CONSTRUCTION:
Round 3", 4" and 6" fixtures with integral LEDs. Isolated external driver factory installed inside junction box.
One driver for every fixture required. Power Factor > 0.95.
LED fixture and driver are TYPE IC rated approved for direct contact with insulation.
Pot light housing is NOT required even for insulated ceilings.
Lifespan: 50,000 hours.
For damp locations
Not waterproof. DO NOT expose to rain.
CERTIFICATION: cETLus. Conforms to UL STD. 1598. Certified to CSA STD. C22.2 NO. 250.0
Driver Input Voltage : 120 V AC (dimmable) (Optional: 277-347V AC for 4"and 6")
Ambient Temperature : -40
Available Light Colours (Kelvin) : Warm White 3000K, Neutral White 4000K and Cool White 5000K
CRI: >80
MODEL:
DISC3-3K/4K/5K
DISC4-3K/4K/5K
DISC6-3K/4K/5K
MOUNTING: Cut hole in ceiling and snap fixture in opening with attached spring clips.
DIMENSIONS:
OD 3-3/4" (94.5mm)
DISC3-3K/4K/5K
OD 5" (125mm)
DISC4-3K/4K/5K
DISC6-3K/ 4K/ 5K OD 7" (175mm)
INSTALL ATION:
ALL FIXTURES MUST BE INSTALLED IN ACCORDANCE WITH CURRENT APPLICABLE ELECTRICAL CODES.
CONNECTING THE DRIVER:
Open the cover of the junction box. Push and remove one of the half-inch knockouts on the side plate. Install standardL16
cable connector. Use double connector for daisy chaining multiple drivers. Insert line voltage feed into the cable connector
and splice same colour wires using wire nuts. Close the cover. Connect the driver to tl'e light fixture the arrows on the
male and female parts of the connector between the driver and the fixture should match. Tighten the connector by hand.
Do not attach the junction box to anything so you can pull it through the ceiling opening in case you need to service the
driver in future.
OPTIONS FOR LOCATING DRIVER:
1. Locate next to the fixture - run line voltage wiring to first junction box and daisy chain to the junction boxes of the
other fixtures.
2. Or install all drivers at one location and use low voltage extension cables to the fixtures . Use only extensions provided by
the manufacturer. Available jumper cables are 10'(3m)(Model# UTLED-JC-10) and 20' (6m)(Model# UTLED-JC-20)
Cables are linkable. Maximum run should not exceed 40'(12m).
DIMMING: We recommend LED/CFL dimmers that have a low range adjustment dial. After all fixtures are connected to the
dimmer adjust the dial to the lowest position before the lights start to flicker of shut down. This setting depends on the
local voltage and number: of fixtures per dimmer.
WARNING :
DO NOT USE ANY OTHER DRIVERS EXCEPT THE ORTECH DRIVERS THAT ARE INCLUDED WITH THE FIXTURE.
DO NOT CONNECT MULTIPLE FIXTURES TO ONE DRIVER.
DO NOT OPEN THE LIGHT FIXTURE AN D THE SIDE PLATES OF THE DRIVER NO SERVICEABLE PARTS INSIDE.
INSTALLATION INSTRUCTIONS FOR LED RECESSED LUMINAIRE
° °
C
C to +40
ENERGY USED:
8W
9W
12W
ID 2-7/8"(74mm)
ID 4-1 /8"(105mm)
ID 6-1 /8"(155mm)
www.ortechindustries.com
I
DISC3-3K DISC3-4K
DISC4-3K / DISC4-4K
DISC6-3K / DISC6-4K / DISC6-5K
LIGHT OUTPUT:
500 Lm
550 Lm
700 Lm
Thickness: 1" (24mm)
Thickness: 1" (25mm)
Thickness: 1" (25mm)
I
DISC3-5K
I
DISC4-5K
EQUIVALENT TO:
50W halogen
60W halogen
75W halogen
Cut out: 3-1 /8" (78 ±3mm)
Cut out: 4-1/4" (108 ±3mm)
Cut out: 6-1/4" (158 ±3mm)