Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: 75902F
Wrenches: 18 & 19mm
Drill Bits: None
For vehicles with appearance panel: Remove plastic
appearance panels which cover driver's and
passenger's side frame rails. Return appearance
panels and fasteners to vehicle owner.
Fasteners typical for all
mounting locations
1 1 1 1
Qty. (5)
Hex Bolt M12 x 1.25 x 35mm CL8.8
1.
Remove and return factory tow hook and fasteners to vehicle owner.
2.
Raise hitch into position on driver's side and loosely install center fastener as shown, installing hex bolt and conical washer thru
elongated hole in hitch into vehicle frame. Raise hitch into position on passenger side and loosely install center fastener as
shown, installing hex bolt and conical washer thru elongated hole in hitch into vehicle frame. Center hitch on vehicle and install
remaining hardware as shown.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2014,2015 Cequent Performance Products
Printed in Mexico
Installation Instructions
Nissan Rogue Select
Tighten all M12 x 1.25 CL8.8 fasteners with torque wrench to 75 Lb.-Ft. (102 N*M)
Sheet 1 of 3
Nissan Rogue
(Except Krōm)
Do Not Exceed Lower of Towing Vehicle
Hitch type
Weight Distribution
Weight Carrying
Ball Mount
Wiring Access Location: SUV3 & 4
21
21
21
21
2 2 2 2
Qty. (5)
Conical Washer ½"
75902N
Part Numbers:
75902
87663
44712
Manufacturer's Rating or
Max Gross
Trailer WT (LB)
Not to be used with Spring bars
3500 (1590 Kg)
Factory Tow Hook
Vehicle Frame
11-13-15
Form: F205 Rev A 5-6-05
Max Tongue
WT (LB)
350 (159 Kg)
Rev. D
Publicité
Manuels Connexes pour Cequent Performance Products 75902
Sommaire des Matières pour Cequent Performance Products 75902
- Page 1 Do not cut access or attachment holes with a torch. This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. 2014,2015 Cequent Performance Products Sheet 1 of 3 75902N 11-13-15 Rev.
- Page 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. 2014,2015 Cequent Performance Products Feuile 2 de 3...
- Page 3 Observe las precauciones de seguridad al trabajar por debajo del vehículo y use protección visual. No corte los orificios de acceso o accesorios con soplete. Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulación V-5 y SAE J684. 2014,2015 Cequent Performance Products Hoja 3 de 3 75902N 11-13-15 Rev.