Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: 75362F
Wrenches: 3/4 , 7/8, 21 mm
Drill Bits: None
Frame
Teeth side
against hitch
1 1 1 1
Qty. (4)
Carriage Bolt 1/2-13 X 1-3/4
2 2 2 2
Qty. (4)
Spacer
Fasteners Typical Both Sides of Vehicle
Note: Factory Installed Steel Step Bumper and Brackets Must Be Used In Conjunction with Hitch
1. Remove existing M14 bolts from end of each frame rail.
2. Lift receiver into position, locating rearmost slots in receiver under existing weldnuts in vehicle frame.
3. Reinstall existing M14 bolts through receiver and frame into existing weldnuts.
4. Install remaining fasteners as shown.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z 2005, 2006, 2009, 2013, 2016 Cequent Performance Products
Printed in Mexico
Installation Instructions
Chevrolet Silverado Pickup
GMC Sierra Pickup
(Requires OEM Bumper)
Note: Factory Installed Steel Step Bumper
and Brackets Must Be Used In
Conjunction with Hitch
Tighten M14 CL10.9 fasteners with torque wrench to 115 Lb.-Ft. (156 N*M)
Tighten all 1/2 GR5 fasteners with torque wrench to 75 Lb.-Ft. (102 N*M)
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
Hitch type
Weight Distributing
Weight Carrying
1
Ball Mount
2
Wiring Access Location: PU3
Factory installed Bumper Bracket
- Typical Both Sides
Existing Weldnut Typical both sides
3
4
Existing M14 bolt
Note: All Fasteners Typical Both Sides of Vehicle
3 3 3 3
Qty. (4)
Conical Washer 1/2
4 4 4 4
Qty. (4)
Hex Nut 1/2-13
Sheet 1 of 3
75362N
Part Numbers:
75362
44564
87186
Max Gross
Max Tongue
Trailer WT (LB)
WT (LB)
8000 (3632 Kg)
900 (409 Kg)
6000 (2724 Kg)
900 (409 Kg)
4-1-16
Rev. H
Form: F205 Rev A 5-6-05
Publicité
Manuels Connexes pour Cequent Performance Products 75362
Sommaire des Matières pour Cequent Performance Products 75362
- Page 1 This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. z 2005, 2006, 2009, 2013, 2016 Cequent Performance Products Sheet 1 of 3 75362N 4-1-16 Rev.
- Page 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. z 2005, 2006, 2009, 2013, 2016 Cequent Performance Products Feuille 2 de 3...
- Page 3 Instrucciones de instalación Números de partes: 75362 CHEVROLET SILVERADO TIPO PICKUP 44564 GMC SIERRA TIPO PICKUP 87186 (REQUIERE PARACHOQUES OEM) VEHÍCULOS CON DIRECCIONALES ÁMBAR Y PARACHOQUES DE FÁBRICA No supere el valor inferior entre la calificación del fabricante del vehículo del remolque o Peso máximo bruto...