Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
H-6375, H-6376
π
H-6377, H-6378
HEAVY DUTY FOLDING
SECURITY GATE
TOOLS NEEDED
Flat Head Screwdriver
1/2" (13 mm) Wrench or Socket
9/16" (14 mm) Wrench or Socket
Axle x 2
2" Standard "L" Bracket x 2
1.
Before installing, decide on gate placement. "L"
brackets that form top hinge allow gate placement
in the recess of door frame. Installation can either
be made outside or inside of wall next to door or
opening frame. (See Figures 1a and 1b)
Outside
"L" Bracket
Figure 1a
NOTE: Either side of gate can be toward the
outside of building. A label on the operating
side (the side with the center pins) indicates
RHT (right) or LFT (left) of a person facing the
operating side.
PAGE 1 OF 6
1-800-295-5510
uline.com
3/4" Masonry Drill Bit
1/4" Masonry or Wood
Drill Bit
Standard Washer x 6
Caster Washer x 4
Carriage Bolt x 6
INSTALLATION
Inside
"L" Bracket
Figure 1b
PARTS NEEDED
5/16 x 2" Long Lag Bolt
Masonry Door Frame or Wall Installations
(Wall Installations may require lead anchors)
PARTS
Bearing Washer x 2
Round Head Bolt x 3
2. Bolt inner and outer panels together at the top,
middle and bottom by using carriage bolts,
standard washers and small nuts. Repeat for
remaining gate panels. (See Figure 2)
CAUTION! Keep hands and fingers out of
moving diamonds of web when handling gate
to avoid pinching.
Para Español, vea páginas 3-4.
Pour le français, consulter les pages 5-6.
Small Nut x 7
Large Nut x 4
2" Caster x 4
Figure 2
0621 IH-6375
Publicité
Manuels Connexes pour Uline H-6375
Sommaire des Matières pour Uline H-6375
- Page 1 Para Español, vea páginas 3-4. Pour le français, consulter les pages 5-6. H-6375, H-6376 π 1-800-295-5510 H-6377, H-6378 uline.com HEAVY DUTY FOLDING SECURITY GATE TOOLS NEEDED Flat Head Screwdriver 3/4" Masonry Drill Bit PARTS NEEDED 5/16 x 2" Long Lag Bolt 1/2"...
- Page 2 Place bearing washer and bottom gate pin back Figure 8 into floor mount. Slip "L" bracket over top of gate and 5/16 x 2" lag bolt (not included.) (See Figure 6) 1-800-295-5510 uline.com PAGE 2 OF 6 0621 IH-6375...
-
Page 3: Herramientas Necesarias
H-6375, H-6376 π 800-295-5510 H-6377, H-6378 uline.mx PUERTA DE SEGURIDAD PLEGABLE DE USO PESADO HERRAMIENTAS NECESARIAS Desarmador de Cabeza Plana Broca de 3/4" para Mampostería PARTES NECESARIAS Perno Largo de 5/16 x 2" Llave o Dado de 13 mm (1/2") Broca de 1/4"... - Page 4 Será más fácil taladrar los orificios guía si quita la puerta de su instalación del piso. Coloque la rondana del balero y el perno inferior de la puerta de regreso a Diagrama 8 800-295-5510 PAGE 4 OF 6 0621 IH-6375 uline.mx...
-
Page 5: Outils Requis
H-6375, H-6376 π 1-800-295-5510 H-6377, H-6378 uline.ca BARRIÈRES DE SÉCURITÉ PLIABLES ROBUSTES OUTILS REQUIS Tournevis à tête plate Mèche à maçonnerie de 3/4 po PIÈCES REQUISES Tire-fond de 5/16 x 2 po Clé ou douille de 13 mm (1/2 po) Mèche à... -
Page 6: Installation Suite
à 3/4 po du plancher. Marquez et percez les avant-trous dans le cadre de porte ou sur le mur. Il sera plus facile de percer les avant-trous si la barrière est retirée de sa Figure 8 1-800-295-5510 uline.ca PAGE 6 OF 6 0621 IH-6375...