WESTEK RFK100 Guide Rapide

Wireless RF Remote Control System
Wall Mounted Switch RFA-108 and Plug-in Receiver RFA-110
This wireless Radio Frequency (RF) control is an easy, convenient way to add switched outlet convenience without any wiring or
electrician needed. The invisible RF signal passes through walls, doors, ceilings, floors and even around corners. Simply plug the
desired appliance into the receiver and the receiver into any outlet. The transmitter is designed to look just like an actual switch and
switchplate and mounts to any surface with the enclosed screws. A press of the transmitter's toggle switch turns whatever you've
plugged into the receiver on or off - just like a hardwired switch and outlet!
Channel Code Information
Three operating channels are available so you can control three separate systems at different locations in your home. Be sure to
match common frequency channels, for those devices you want operated by the same switch.
INSTRUCTIONS
Notes: The total load of appliances connected to the Plug-in Receiver
should not exceed 1200 Watts or 10 Amps.
Do not use Plug-in Receiver to control appliance loads that may be
dangerous to turn on remotely (i.e. power tools).
The Plug-in Receiver must be located within 100 feet of the Wall
Transmitter.
•
Remove Front Cover of Wall Transmitter by turning the two white
Cover Screws on the Front Cover counter-clockwise.
•
Remove plastic Battery Tab by gently pulling it from Battery
Compartment (this tab isolates the battery until it's ready for use
and insures that you'll have a fresh battery).
•
Reinstall Front Cover using 2 Cover Screws. Set Wall Transmitter
aside.
•
Plug your light/appliance into the outlet on the Receiver being
careful to match the wide blade of the light/appliance (if equipped)
with the wide slot on the outlet.
•
Plug the Receiver into any standard grounded 110/120 Volt outlet
being careful to match the wide blade of the Receiver with the wide
slot on the outlet. Fully insert.
•
Before mounting your Wall Transmitter, hold your Wall Transmitter
at the location where you wish to install.
•
Press Toggle Switch to determine if your light/appliance turns on and
off. If your light/appliance does not respond try relocating the
Transmitter or Receiver. Large metal objects such as metal doors or
cabinets should not be in the way of the Wall Transmitter and
Plug-in Receiver since this could decrease the range of the RF signal.
•
Once you have succesfully completed this test, remove Front Cover
once again and mount Wall Transmitter with two enclosed
Mounting Screws. (Surfaces other than wood may require different
type of mounting hardware.)
•
Replace Front Cover of Wall Transmitter and secure to wall switch
with white Cover Screws (do not overtighten).
OPERATION
Simply press the Toggle Switch to turn the light/appliance you've
plugged into the Receiver on or off.
Note: Wait at least 3 seconds after you press the transmitter on or off
before you press it again. This allows for the RF signal transmission to
be completed.
BATTERY REPLACEMENT
Your RFK100 battery should last 2-3 years under normal use.
To replace battery:
•
Remove Front Cover of Wall Transmitter by turning the two white
Cover Screws on the Front counter-clockwise.
•
Remove battery from Battery Compartment and replace with
another 12Volt battery (Radio Shack™ 23, 23M, VR22, EL22 or
equivalent).
•
Replace Front Cover and Screw.
Caution
This device complies with Part 15 of the FCC. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may
cause undesired operation.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates uses and can radiate radio frequency
MOUNTING
SCREWS
FRONT
COVER
COVER
SCREWS
TOGGLE
SWITCH
Troubleshooting Guide
SYMPTOM PROBABLE CAUSE
Light does not
turn on.
Light does not
turn off.
Light comes
on randomly.
SPECIFICATIONS
Receiver:RFA-110:
120V~60Hz 10A Resistive load,
240W tungsten lamp load
FCC ID: XDE-RFA110
Transmitter:RFA-108:
Battery 12VDC, 315MHz
FCC ID: XDE-RFA108
Plug-in receiver for indoor use only.
©2016 AmerTac™
250 Boulder Drive
Breinigsville, PA 18031
610-336-1330
www.amertac.com
Made in China / Hecho en China /
Fabriqué en Chine
I16-0016-A
One-Year Limited Warranty: AmerTac warrants to the original
purchaser that this product will be free from defects in materials and
workmanship for a period of one year from the date of purchase. Additional
details are available at www.amertac.com. Prop.65 WARNING: This
product contains chemicals known to the State of California to cause cancer
and/or birth defects or other reproductive harm.
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
RFK100, RFK100L
BATTERY TAB
COMPARTMENT
1. Circut breaker or fuse is turned
off.
2. Switch on lamp is turned off.
3. Bulb is defective.
4. Weak battery.
5. Lamp module or lamp is loose.
1. Transmitter signals are being
blocked. Check for metal objects
that could block the signal, or
reposition the transmitter.
2. Switching too fast. Wait 3
seconds between toggles.
3. Weak battery.
1. Short term power line failure.
2. Transmitter out of range.
3. Lamp module or lamp is loose.
3154847
CONFORMS TO UL STD 61058-1 AND 498A
CERTIFIED TO CSA STD C22.2 No.61058-1
AND No.42
ACATA EL ESTÁNDAR DE UL 61058.1 y
498A
CERTIFICADO DE ACUERDO AL ESTÁNDAR
CSA C22.2 NÚM. 61058.1 y NÚM. 42
CONFORME À LA NORME UL 61058.1 ou
498A
CERTIFIÉ CONFORMÉMENT À LA NORME
CSA C22.2 N° 61058.1 ou N° 42
BATTERY