OttLite Learning Light J82K26 Mode D'emploi

C
B
C
D
A
The Learning Light
®
J82K26 J48286 J48006 626218 J48806
GX7908
REV062113
ENGLISH
CONGRATULATIONS! 3. Raise the shade so access to the
You've purchased the finest in tube is possible.
natural lighting technology with
4. To install a tube in the socket,
your new OttLite product.
®
hold the tube firmly at the non-base
PRODUCT REGISTRATION FORM end with thumb and forefinger. Align
into socket, then press the base
Please complete the enclosed
Product Registration Form and into the socket until it "snaps" into
return it today by mail, or register place (B).
online by going to: http://warranty.
OttLite.com. 5. To remove a tube already
installed in the lamp, grasp it firmly
WARNING: To prevent electric at the free end between thumb and
shock, make sure the lamp is not forefinger. Use free hand to push
plugged in until all assembly steps fingers and tube away from the
are complete. socket. Do not twist or turn the
tube.
LAMP ASSEMBLY
1. Align base as shown. Install base CAUTION: Take care to prevent the
tube end from hitting the shade.
screw loosely by hand.
Tube breakage may result.
2. Using a screwdriver, tighten base
screw until snug (A). 6. Return shade to desired position.
OPERATION 7. Plug lamp into a standard 120V,
1. As needed, tighten or loosen the 60Hz socket. Your lamp is ready
two pivot joints (C) using a coin. Be to use.
careful to not overtighten the joints.
8. Turn lamp on or off by using
2. Shade height and angle can be
rocker switch (D).
changed by grasping the shade and
base and moving it up or down. Please note that in operation,
OttLite
3. The shade can also be rotated
right and left at the upper joint. Enjoy your OttLite
TUBE INSERTION/REPLACEMENT
This lighting system is designed
1. Make sure the lamp is not
for use with OttLite
plugged into an electrical socket.
(model number PL13-E
other products voids the warranty
2. If the lamp has been in use, allow
and may result in damage to the
it to cool approximately 5 minutes
lighting system.
before proceeding.
For more information on purchasing replacementv tubes/
bulbs please go to www.OttLite.com/replacement13wtube
CAUTION!
If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced by the manufacturer
or its service agent or a similar qualified person in order to avoid a hazard. Indoor use only.
The Learning Light ®
CAUTION! IMPORTANT SAFETY INSTRUCTIONS:
THIS PORTABLE LAMP HAS A POLARIZED PLUG (ONE BLADE IS WIDER THAN THE OTHER) AS A FEATURE TO
REDUCE THE RISK OF ELECTRIC SHOCK. THIS PLUG WILL FIT IN A POLARIZED OUTLET ONLY ONE WAY. IF THE
PLUG DOES NOT FIT FULLY IN THE OUTLET, REVERSE THE PLUG. IF IT STILL DOES NOT FIT, CONTACT A
QUALIFIED ELECTRICIAN. NEVER USE WITH AN EXTENSION CORD UNLESS PLUG CAN BE FULLY INSERTED.
DO NOT ALTER THE PLUG.
CAUTION:
FULLY INSERT.
AVERTISSEMENT! IMPORTANTES DIRECTIVES DE
SÉCURITÉ:
CETTE LAMPE PORTATIVE EST MUNIE D'UNE FICHE POLARISÉE (UNE LAME PLUS LARGE QUE L'AUTRE). CE
DISPOSITIF DE SÉCURITÉ DIMINUE LE RISQUE DE CHOCS ÉLECTRIQUES PUISQUE LA FICHE NE S'INSÈRE DANS
LA PRISE QUE D'UN SEUL CÔTÉ. SI ELLE N'ENTRE PAS DANS LA PRISE, INVERSEZ-LA. SI ELLE N'ENTRE
TOUJOURS PAS, CONTACTEZ UN ÉLECTRICIEN QUALIFIÉ. N'UTILISEZ JAMAIS AVEC UNE RALLONGE SAUF SI
LA FICHE S'INSÈRE ENTIÈREMENT. NE MODIFIEZ PAS CE DISPOSITIF DE SÉCURITÉ.
AVERTISSEMENT:
DANS LA GRANDE FENTE ET POUSSEZ JUSQU'AU BOUT.
® tubes are not dimmable.
® Learning Light!
tubes only ¡ PRECAUCIÓN! INSTRUCCIONES DE SEGURIDAD IMPORTANTES:
®
. Use of
ESTA LÁMPARA PORTÁTIL TIENE UN ENCHUFE POLARIZADO (UNA DE SUS PATAS ES MÁS ANCHA QUE LA OTRA)
COMO CARACTERISTICA PARA REDUCIR EL RIESGO DE UNA DESCARGA ELÉCTRICA. ESTE ENCHUFE ENCAJARÁ EN
CUALQUIER TOMACORRIENTE POLARIZADO SOLO DE UNA MANERA. SI EL ENCHUFE NO CALZA COMPLETAMENTE
EN EL TOMACORRIENTE DÉLE LA VUELTA. SI AÚN NO ENCAJA, PÓNGASE EN CONTACTO CON UN ELECTRICISTA
CALIFICADO. NUNCA UTILICE UNA EXTENSIÓN A NO SER QUE EL ENCHUFE PUEDA SER TOTALMENTE
INSERTADO. NO ALTERE EL ENCHUFE.
PRECAUCIÓN:
ENCHUFE CON LA RANURA ANCHA, INSERTE TOTALMENTE.
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT,
POUR ÉVITER LES CHOCS ÉLECTRIQUE, INSÉREZ LE BOUT LARGE DE LA FICHE
PARA PREVENIR UNA DESCARGA ELÉCTRICA, HAGA COINCIDIR LA PATA ANCHA DEL