Jasco 46564 Manuel

FCC / IC
En
This device complies with Part 15 of the FCC and Industry Canada license-exempt RSS
standards. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
FCC NOTE: The manufacturer is not responsible for any radio or TV interference caused
by unauthorized modifications to this equipment. Such modifications could void the user's
authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy, and if not installed and used in accordance with
the instructions may cause harmful interference to radio communications. However, there is no
guarantee interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct theinterference by one or more of
the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
— Consult the dealer or an experienced radio/TV technician for help
Important note: To comply with the FCC RF exposure compliance requirements, no change
to the antenna or the device is permitted. Any change to the antenna or the device could result
in the device exceeding the RF exposure requirements and void user's authority to operate
the device.
Fr
Cet appareil est conforme au paragraphe 15 des normes FCC et au CNR pour les appareils
exempts de licence d'Industrie Canada. Son utilisation est sujette aux deux conditions
suivantes : (1) cet appareil ne doit pas occasionner de brouillage préjudiciable et (2) cet
appareil doit accepter toutes les interférences reçues, notamment les interférences qui peuvent
provoquer un fonctionnement non désiré.
NOTE DE LA FCC : Le fabricant n'est pas responsable des interférences sur les fréquences
radioélectriques ou télévisuelles pouvant être causées par des modifications non autorisées de
ce matériel. De telles modifications peuvent annuler le droit de l'utilisateur à utiliser cet appareil.
REMARQUE : Cet appareil a été testé et certifié conforme aux limites relatives aux appareils
numériques de catégorie B définies dans le paragraphe 15 des normes FCC. Ces limites
ont été définies afin de fournir une protection raisonnable contre le brouillage préjudiciable
en milieu résidentiel. Cet appareil produit, utilise et peut émettre des ondes de fréquence
radio et, s'il n'est pas installé et utilisé conformément aux instructions, il peut provoquer un
brouillage préjudiciable aux communications radio. Il n'existe toutefois aucune garantie que
des interférences ne se produiront pas au sein d'une installation donnée. Si cet appareil
occasionne un brouillage préjudiciable à la réception radiophonique ou télévisuelle, il suffit
d'allumer et d'éteindre l'appareil pour déterminer sa responsabilité. Nous encourageons
l'utilisateur à essayer de corriger ces interférences en appliquant une ou plusieurs des mesures
suivantes :
— Réorienter ou déplacer l'antenne de réception.
— Augmenter la distance entre l'appareil et le récepteur.
— Brancher l'appareil à une prise secteur différente de celle du récepteur.
— Consulter le revendeur ou un technicien spécialisé en postes radio ou téléviseurs.
Remarque importante : Pour se conformer aux exigences de conformité de la FCC
concernant l'exposition aux RF, aucune modification apportée à l'antenne ou au dispositif n'est
autorisée. Toute modification apportée à l'antenne ou au dispositif pourrait faire en sorte que le
dispositif dépasse les exigences d'exposition aux RF et pourrait annuler le droit de l'utilisateur
à utiliser ce dispositif.
Es
Este dispositivo cumple con las Especificaciones del apartado 15 de las normas de la FCC
y con las especificaciones de las normas radioeléctricas (RSS) del Ministerio de Industria
de Canadá aplicables a aparatos exentos de licencia. El funcionamiento está sujeto a las
siguientes dos condiciones: (1) este dispositivo no debe provocar interferencia perjudicial, y (2)
este dispositivo debe aceptar toda interferencia que reciba, incluso la que pudiera causar un
funcionamiento no deseado.
NOTA DE LA FCC: El fabricante no se hace responsable de ninguna interferencia de radio
o TV ocasionada por modificaciones no autorizadas efectuadas a este equipo. Dichas
modificaciones podrían anular la autoridad del usuario para utilizar el equipo.
NOTA: Este equipo ha sido probado y cumple con los límites para aparatos digitales de
Clase B, de conformidad con el apartado 15 de las normas de la FCC. Estos límites están
diseñados para proveer protección razonable contra interferencias perjudiciales en una
instalación residencial. Este equipo genera, usa y puede irradiar energía de radiofrecuencias
y, si no se instala y usa según las instrucciones, puede provocar interferencia perjudicial a las
radiocomunicaciones. No obstante, no hay garantías de que no ocurrirá interferencia en una
instalación en particular. Si este equipo provoca interferencia perjudicial a la recepción de radio
o televisión, lo que puede determinarse encendiendo y apagando el equipo, se recomienda
que el usuario intente corregir la interferencia por medio de la implementación de una o más
de las siguientes medidas:
— Reorientar o reubicar la antena receptora.
— Incrementar la separación entre el equipo y el receptor.
— Conectar el equipo a un tomacorriente de un circuito diferente del circuito al que está
conectado el receptor.
— Consultar al distribuidor o a un técnico con experiencia en radio/televisión para
solicitar asistencia.
Nota importante: Para cumplir con los requisitos de cumplimiento de exposición de
radiofrecuencia de la FCC, no se permiten cambios a la antena o el dispositivo. Cualquier
cambio a la antena o dispositivo podría hacer que el dispositivo supere los requerimientos de
exposición de radiofrecuencia y anular la autoridad del usuario para operar el dispositivo.
Responsible Party - US Contact Information | Parte responsable - Información de
contacto de los Estados Unidos | Partie responsable - Coordonnées des États-Unis
FCC — U2ZZW3010 | IC: 6924A-ZW3010
Jasco Products Company | Model: ZW3010/46564
10 E. Memorial Rd., Oklahoma City, OK 73114 | 1-800-654-8483
CAN ICES-3(B)/NMB-3(B)
All brand names shown are trademarks of their MADE IN CHINA/FABRIQUÉ EN CHINE/HECHO
respective owners. EN CHINA
DISTRIBUTED BY
Tous les noms de marque illustrés sont des
JASCO PRODUCTS COMPANY LLC,
marques de commerce de leurs propriétaires
respectifs. 10 E. MEMORIAL RD.,
OKLAHOMA CITY, OK 73114.
Todas las marcas que aparecen aquí
©JASCO 2019 | 46564 | ZW3010 | 3/19/19 v1
son marcas registradas de sus respectivos dueños.
1.
Tools You Will Need
IMPORTANT!
The fixture controlled by the Z-Wave In-Wall Smart Dimmer must not
exceed 600W (incandescent); 300W dimmable CFL/LED. The dimmer is
designed only for use with permanently installed fixtures.
Getting to know your new Z-Wave device
• Turn ON/OFF and adjust dim levels manually or remotely via the Z-Wave
controller
• Can be included in multiple groups and scenes
• May be used in single pole installation or with up to four Jasco Add-on Switches in
3-way or 4-way wiring configurations
• Compatible with all incandescent and most dimmable CFL/LED bulbs
• Auto line/load detection
• Interchangeable paddle switch — white & light almond paddle in package
• Uses a standard, decorative-size wall plate for single-gang installations
(wallplate not included)
• Blue LED indicates dimmer location in a dark room
• Z-Wave certified for simple pairing and integrated home automation
• Screw terminal installation — requires wiring connections for line (hot), load,
neutral and ground. Traveler wire required for 3-way or 4-way installation
• This Z-Wave device has advanced features that allow you to customize your
experience. These features can only be adjusted by a Z-Wave enabled controller
that supports the Z-Wave configuration command class. For a complete list of
adjustable configurations, visit www.ezzwave.com/config
2.
A
F
B D
G
C
E
A. Ground (Green/Bare) F. Top rocker — Press & release
to turn dimmer ON, press &
B. Line or Load (Black)
hold increases brightness
C. Line or Load (Black)
G. Bottom rocker — Press
D. Traveler (Red/Other) & release to turn dimmer
OFF, press & hold to dim
E. Neutral (White)
MANUAL • MANUEL • MANUAL
In-Wall
READ IT OR WATCH IT
Smart Dimmer
Montage mural
intelligent Gradateur
Read instructions or watch easy-to-follow
video. Scan QR code or visit goo.gl/22xkHv
sans fil
Interruptor
de pared
reductor
inalàmbricode
luz inteligente
Convert any smart control* to a multi-location switch
*For a list of compatible devices, visit ezzwave.com
Smart Control Add-On Switches
To purchase an add-on switch or for more details, visit
ezaddonswitch.com.
Multiple Paddle
Colors Available
ezzwave.com/paddlecolors
Purchase additional items at
EZzwave.com or visit your local retailer.
In-Wall Plug-in In-Wall
Smart Dimmers Smart Dimmers Add-on Switches
In-Wall Motion Switch Plug-in In-Wall
or Dimmer Smart Switches Smart Switches
Enbrighten In-Wall Hinge Pin
Smart LED Bulb Smart Fan Control Smart Door Sensor
Direct Wire, Portable In-Wall
40A Outdoor Smart Multi Tamper-Resistant Outdoor Smart
Smart Switch Sensor Smart Outlet
OR
OR
WARNING — SHOCK HAZARD
Turn OFF the power to the branch circuit for the dimmer and lighting fixture at the
service panel. All wiring connections must be made with the POWER OFF to avoid
personal injury and/or damage to the dimmer.
This device is intended for installation in accordance with the National Electric Code
and local regulations in the United States or the Canadian Electrical Code and local
regulations in Canada. If you are unsure or uncomfortable about performing this
installation, consult a qualified electrician.
Multi-switch wiring
For 3-way installations, please refer to Jasco Add-on Switch manual
Single switch wiring
Before installation, you may wish to change the paddle color to
match your wallplate or decor. Please proceed to section 5.
1. Shut off power to the circuit at circuit breaker or fuse box.
IMPORTANT! Verify power is OFF to switch box before continuing.
2. Remove wallplate.
3. Remove the switch mounting screws.
4. Carefully remove the switch from the switch box. DO NOT disconnect the wires.
There are up to five screw terminals on the switch; these are marked:
A. GROUND — Green/Bare
B. LINE OR LOAD — Black (connected to power or lighting)
C. LINE OR LOAD — Black (connected to power or lighting)
4.
Adding your device to a Z-Wave network To remove and reset the device
1. Follow the instructions for your Z-Wave certified controller 1. Follow the instructions for your Z-Wave certified controller
to add a device to the Z-Wave network.
2. Once the controller is ready to add your device, press 2. Once the controller is ready to remove your device,
and release the top or bottom of the wireless smart
dimmer (rocker).
To return your switch to factory defaults
Now you have complete control to turn your fixture ON/OFF
1. Quickly press ON (top) button three times then
according to groups, scenes, schedules and interactive
automations programmed by your controller.
If your Z-Wave certified controller features remote access,
you can control your fixture from your mobile devices. Note: This should only be used if your network's primary
controller is missing or otherwise inoperable.
DO NOT RETURN THIS
PRODUCT TO THE STORE
STOP
NE RETOURNEZ PAS
CE PRODUIT AU MAGASIN
NO DEVUELVA ESTE
PRODUCTO A LA TIENDA
If you have any problems or questions, contact our U.S.-based Consumer Care at
1-800-654-8483, option 1, Monday–Friday, 7:00AM–8:00PM CST.
For the most up-to-date product support, accessories, electronic (PDF) format manuals
and more, visit www.byjasco.com/support.
• No user-serviceable parts in this unit.
Si vous avez des problèmes ou des questions, veuillez communiquer avec notre
service à la clientèle aux États-Unis au 1-800-654-8483, option 1, du lundi au
vendredi, de 7 h à 20 h (HNC).
46564
Pour un soutien technique d'avant-garde, les nouveaux accessoires, les plus
ZW3010
récents manuels en format électronique (PDF) et plus encore, visitez le site www.
byjasco.com/support.
• Aucune des pièces de ce dispositif ne peut être réparée par l'utilisateur.
Si tiene problemas o dudas, comuníquese con nuestro Centro de atención al
cliente con sede en EE. UU. al 1-800-654-8483, opción 1, de lunes a viernes, de
7.00 a 20.00 h, hora estándar del centro (CST).
Para recibir el soporte técnico más actualizado sobre productos, accesorios,
manuales en formato digital (PDF), entre otros, visite www.byjasco.com/support
• Esta unidad no contiene piezas que el usuario pueda reparar.
WARNING ADVERTENCIA
RISK OF FIRE RIESGO DE INCENDIO
RISK OF ELECTRICAL SHOCK RIESGO DE DESCARGA ELÉCTRICA
RISK OF BURNS RIESGO DE QUEMADURAS
CONTROLLING APPLIANCES
CONTROL DE EQUIPOS ELECTRODOMÉSTICOS
CAUTION: PRECAUCIÓN:
A FIN DE DISMINUIR EL RIESGO DE RECALENTAMIENTO
TO REDUCE THE RISK OF OVERHEATING AND POSSIBLE
DAMAGE TO OTHER EQUIPMENT, DO NOT INSTALL TO Y DE POSIBLES DAÑOS EN LOS DEMÁS EQUIPOS,
CONTROL A RECEPTACLE, MOTOR-OPERATED APPLIANCE, NO INSTALAR PARA CONTROLAR UN RECEPTOR, UN
APARATOS QUE FUNCIONAN A MOTOR, ARTEFACTOS
FLUORESCENT LIGHTING FIXTURE OR TRANSFORMER-
SUPPLIED APPLIANCE. DE ILUMINACIÓN DE LUZ FLUORESCENTE O APARATOS
ALIMENTADOS CON TRANSFORMADORES.
• ONLY USE TO CONTROL INCANDESCENT OR DIMMABLE
CFL/LED BULBS • USAR EXCLUSIVAMENTE PARA CONTROLAR
• DO NOT EXCEED RATINGS BOMBILLAS CFL/LED INCANDESCENTES O
ATENUABLES
• DO NOT USE TO CONTROL ANY DEVICE WHERE
UNINTENDED OPERATION COULD CAUSE UNSAFE • NO SUPERE LOS VALORES NOMINALES ELÉCTRICOS
CONDITIONS (HEAT LAMP, SUN LAMP, ETC.) • NO USAR PARA CONTROLAR DISPOSITIVOS EN LOS
QUE EL FUNCIONAMIENTO NO INTENCIONADO
• DO NOT USE TO CONTROL RECEPTACLES
• FOR INDOOR USE ONLY PODRÍA PROVOCAR SITUACIONES PELIGROSAS
AVERTISSEMENT
(LÁMPARAS DE CALEFACCIÓN, LÁMPARAS SOLARES,
ETC.)
• NO UTILICE PARA CONTROLAR TOMACORRIENTES.
RISQUE D'INCENDIE
• USE SOLAMENTE EN INTERIORES
RISQUE DE CHOC ÉLECTRIQUE
RISQUE DE BRÛLURES
NOT FOR USE WITH MEDICAL OR LIFE-SUPPORT
COMMANDE DES APPAREILS
EQUIPMENT
ATTENTION:
Z-WAVE ENABLED DEVICES SHOULD NEVER BE USED TO
POUR RÉDUIRE LE RISQUE DE SURCHAUFFE ET DE
SUPPLY POWER TO OR CONTROL THE ON/OFF STATUS
DOMMAGES POSSIBLES À D' A UTRES APPAREILS, NE
OF MEDICAL OR LIFE-SUPPORT EQUIPMENT.
PAS INSTALLER POUR COMMANDER UN RÉCEPTEUR,
NE PAS UTILISER AVEC UN ÉQUIPEMENT MÉDICAL
UN APPAREIL ACTIONNÉ PAR MOTEUR, UN APPAREIL
OU DE SURVIE
D'ÉCLAIRAGE FLUORESCENT OU UN APPAREIL
LES DISPOSITIFS COMPATIBLES AVEC LA TECHNOLOGIE
ALIMENTÉ PAR UN TRANSFORMATEUR.
• UTILISER SEULEMENT POUR COMMANDER Z-WAVE NE DEVRAIENT JAMAIS ÊTRE UTILISÉS POUR
ALIMENTER OU COMMANDER LA MISE EN MARCHE OU
LES AMPOULES À DEL ET FLUOCOMPACTES À
L'ARRÊT DE L'ÉQUIPEMENT MÉDICAL OU DE SURVIE.
INCANDESCENCE OU À INTENSITÉ RÉGLABLE
• NE PAS DÉPASSER LES CARACTÉRISTIQUES
SE PROHÍBE SU EMPLEO EN EQUIPO MÉDICO
NOMINALES
O EQUIPO PARA EL MANTENIMIENTO DE LAS
• NE PAS UTILISER POUR COMMANDER DES
FUNCIONES VITALES
APPAREILS POUR LESQUELS UN FONCTIONNEMENT
LOS DISPOSITIVOS Z-WAVE NUNCA SE DEBEN USAR
IMPRÉVU POURRAIT ENTRAÎNER DES CONDITIONS
PARA SUMINISTRAR ENERGÍA ELÉCTRICA AL EQUIPO
DANGEREUSES (LAMPE À RAYONS INFRAROUGES,
MÉDICO O AL EQUIPO PARA EL MANTENIMIENTO DE
LAMPE SOLAIRE, ETC.)
FUNCIONES VITALES, NI PARA CONTROLAR EL ESTADO
• NE PAS UTILISER POUR COMMANDER LES PRISES
DE ENCENDIDO O APAGADO DE DICHOS EQUIPOS.
DE COURANT
• POUR UTILISATION INTÉRIEURE UNIQUEMENT
Plug-in
Switch
Insert wires into holes, do not wrap wires
around screws.
Do not remove screws.
B
D
E
A
C
D. TRAVELER — Red/Other (only in 3-way installations)
E. NEUTRAL — White
Match these screw terminals to the wires connected to the existing switch.
5. Disconnect the wires from the existing switch. Label wires
according to the previous terminal connection.
Observe important wiring information
IMPORTANT! This dimmer is rated for and intended
to only be used with copper wire.
Wire gauge requirements
Use 14AWG or larger wires suitable for at least 80° C for supplying
line (hot), load, neutral, ground and traveler connections.
Wire strip length:
For attachment to screw terminals, strip insulation 1in. (25mm).
For attachment using the enclosure's holes, strip insulation 5/8in. (16mm).
UL specifies the tightening torque for the screws is 14Kgf-cm (12lbf-in).
1. Connect the green or bare copper ground wire to the GROUND terminal.
2. Connect the black wire from the light to either LINE/LOAD. terminal.
3. Connect the black wire from the electrical service panel (hot) to either
LINE/LOAD terminal.
4. Connect the white wire to the NEUTRAL terminal (use a jumper wire if needed).
Note: The traveler terminal is only used for 3-way or 4-way wiring and should remain
insulated if the dimmer is being installed in a 2-way system (one switch & one load).
5. Insert dimmer into the switch box being careful not to pinch or crush wires.
6. Dimmer must be independently mounted (vertical position only).
5.
to remove a device from the Z-Wave network.
press and release the top or bottom of the wireless smart
dimmer (rocker).
immediately press the OFF (bottom) button three times.
The LED will flash ON/OFF five times when completed
Z-WAVE INTEROPERABILITY
successfully.
This product can be added and operated in any
Z-Wave network with other Z-Wave certified
devices from other manufacturers and/or other
applications. All non-battery operated nodes
within the network will act as repeaters regardless
of vendor to increase reliability of the network.
WARRANTY
Jasco Products Company warrants this product to be free from manufacturing defects two years
from the original date of consumer purchase. This warranty is limited to the repair or replacement of
this product only and does not extend to consequential or incidental damage to other products that
may be used with this product. This warranty is in lieu of all other warranties, expressed or implied.
Some states do not allow limitations on how long an implied warranty lasts or permit the exclusion
or limitation of incidental or consequential damage, so the above limitations may not apply to you.
This warranty gives you specific rights, and you may also have other rights which vary from state
to state. Please contact our U.S.-based Consumer Care at 1-800-654-8483 (option 1) between
7AM – 8PM CST or www.byjasco.com if the unit should prove defective within the warranty period.
GARANTIE
Jasco Products Company garantit que ce produit est exempt de tout défaut de fabrication pour
une période de deux ans à compter de la date de l'achat original par l'acheteur. Cette garantie
se limite exclusivement à la réparation ou au remplacement de ce produit et n'est pas applicable
aux dommages indirects ou accessoires survenus sur d'autres produits utilisés avec ce produit.
Cette garantie se substitue à toute autre garantie expresse ou implicite. Certains États ne
permettent pas de restrictions quant à la durée d'une garantie implicite ou permettent l'exclusion
ou la limitation des dommages indirects et accessoires; il se peut, par conséquent, que cette
garantie ne s'applique pas dans votre cas. Cette garantie vous confère des droits juridiques précis;
vous pouvez jouir d'autres droits qui peuvent varier d'un État à l'autre. Veuillez communiquer
avec notre service à la clientèle aux États-Unis au 1-800-654-8483 (option 1) entre 7 h et 20 h
(HNC) ou www.byjasco.com si l'appareil s'avère défaillant au cours de la période de garantie.
GARANTÍA
Jasco Products Company garantiza que este producto no tendrá defectos de fabricación durante dos
años a partir de la fecha de compra del consumidor original. Esta garantía se limita a la reparación
o reposición de este producto y no cubre daños indirectos o incidentales a otros productos que
se pudieran utilizar con este producto. Esta garantía reemplaza cualquier otra garantía explícita
o implícita. Algunos estados no permiten la aplicación de limitaciones respecto de la duración de
una garantía implícita o permiten la exclusión o limitación de la cláusula sobre daños indirectos o
incidentales, por este motivo las limitaciones arriba mencionadas pueden no aplicarse en su caso.
Esta garantía le otorga derechos específicos y es posible que tenga otros derechos que pueden variar
según el estado en el que vive. Por favor, comuníquese con nuestro Centro de atención al cliente con
sede en EE. UU. al 1-800-654-8483 (opción 1) entre las 7.00 a 20.00 h, hora estándar del centro (CST)
o www.byjasco.com en caso de que se produzca algún defecto durante la vigencia de la garantía.
Jasco Products Company LLC, Building B
10 E. Memorial Rd. Oklahoma City, OK 73114.
SPECIFICATIONS
ZW3010
Power: 120VAC, 60Hz
Signal (Frequency): 908.4/916MHz
Maximum loads: 600W, 2-gang 500W or 3-gang 400W incandescent, 300W CFL/LED
Range: Up to 150ft. line of sight between the wireless controller and the closest Z-Wave
receiver module.
Operating temperature range: 32-104° F (0-40° C)
Type 1 enclosure, independetly mounted (vertical position only), operating control: type 1.c
action, pollution degree (2), impulse voltage (2500V), software class A
For indoor use only
Specifications subject to change without notice due to continuing product improvement
SPÉCIFICATIONS
ZW3010
Tension : 120VCA, 60Hz
Signal (fréquence) : 908.4/916MHz
Charges maximales : 600W, 2 compartiments 500W, 3 compartiments 400W lampes à
incandescent 300W CFL/LED
Portée : Distance à vue entre la télécommande et le module de réception Z-Wave le plus
proche allant jusqu'à 150 pi (45.7m)
Plage de températures de fonctionnement : de 32 à 104° F (de 0 à 40° C)
Boîtier de type 1, monté indépendamment (position verticale seulement), intervention de
type 1.c commande de fonctionnement, degré de pollution (2), tension de choc de (2500V),
logiciel de classe A
Utilisation intérieure uniquement
En raison d'améliorations continues du produit, les spécifications peuvent faire l'objet de
changements sans préavis
ESPECIFICACIONES:
ZW3010
Alimentación: 120VAC, 60Hz
Señal (frecuencia): 908.4/916MHz
Cargas máximas: 600W, Caja para 2 conexiones 500W, Caja para 3 conexiones 400W sólo
las lámparas incandescente 300W CFL/LED
Alcance: Hasta 150 pies (45.7m) en línea de visión directa entre el control remoto
inalámbrico y el módulo receptor Z-Wave más cercano
Rango de temperatura de funcionamiento: 32-104° F (0-40° C)
Recinto de tipo 1, independientemente montado (solo en posición vertical), control de
operación: acción tipo 1.c, grado de contaminación (2), voltaje de impulso (2500V), software
de clase A
Para uso en espacios interiores solamente
Especificaciones sujetas a cambio sin aviso debido a continuas mejoras del producto
Out to Light (Load)
B
A
D
E
C
From Breaker Box
7. Secure the dimmer to the box using the supplied screws.
8. Mount the wallplate.
9. Reapply power to the circuit at fuse box or circuit breaker and test the system.
Basic operation
The connected light can be turned ON/OFF and adjust dim levels in two ways:
1. Manually from the front panel of the dimmer.
2. Remotely with a Z-Wave controller.
Manual control
The front panel rocker dimmer allows the user to:
Turn ON/OFF the connected fixture.
1. To turn the connected fixture ON, press and release the top of the rocker.
2. To turn the connected fixture OFF, press and release the bottom of the rocker.
Adjust dim levels
1. To increase brightness, press and hold the top of the rocker.
2. To decrease brightness, press and hold the bottom of the rocker.
Cycle LED light
The LED below the dimmer acts as a guide light or status indicator.
How to cycle through options: Press up three times and down once quickly.
1. LED is ON when the load is off (guide light in the dark) (default)
2. LED is ON when the load is ON (indicates the dimmer is ON)
3. LED is always OFF
4. LED is always ON (illuminates dimmer in the dark)
Changing paddle color
The Jasco Add-on Switch is required
This step is optional. Before installation, for multi-switch 3-way or
you may want to change the color of the
4-way installations.
paddle to match your wallplate or decor. Connecting the traveler terminal of this
2.
1. Lift the air gap tab at the base of the
dimmer to a standard, non-Jasco switch
paddle.
will cause damage or result in improper
2. Push side tabs in on one side and then
function. If this dimmer is a part of a
the other to release paddle. Lift the 3-way or 4-way multi-switch installation,
cover up and off.
do not connect the traveler wire or apply
3. Simply put the new paddle onto the
power until Jasco Add-on Switches are
dimmer by inserting the air gap and correctly installed. For more information
side tabs and snapping securely into on 3-way or 4-way installations, view
1.
place.
the manual or quick-start guide that for
the Jasco Add-on Switch.
Once this step has been completed return
to section 3.
This device supports Association Command Class (3 Groups)
• Association Group 1 supports Lifeline, Multi-level Switch report
• Association Group 2 supports Basic Set and is controlled with the local load
• Association Group 3 supports Basic Set and is controlled by double pressing the
ON/OFF button
• Each Association Group supports 5 total nodes
NOTE: Actual performance of any CFL or LED will vary from bulb type to bulb type and
among different manufacturers. It is important to note only bulbs designed as dimmable
should be used on a dimmer. To find out if your bulb is dimmable, please check the
package, the bulb itself or call the bulb manufacturer directly.
For a complete list of recommended CFL/LED bulbs for this and other Z-Wave
products from Jasco, please vist www.ezzwave.com.