Sommaire des Matières pour Actiontec electronic T2200H
- Page 1 Actiontec Electronics, Inc. 760 North Mary Ave., Sunnyvale, CA 94085 USA Wireless 11n VDSL2 Modem Gateway Model #: T2200H, T1200H Quick Start Guide Version: 2.0 (Draft to be review) ...
- Page 2 Connect the Gateway to a Computer 1. Get T2200H/T1200 router from the Quick Start Kit and take it out of the bag. 2. Get the Power Cord from your DSL Quick Start Kit. (Power: External, 12V DC, 1.8A; Model: STD‐12018U1) 3. Plug the smaller end of the Power Cord into the Black Port on the back of the Gateway. 4. Plug the larger end of the Power Cord into a Power Outlet. 5. Make sure the Power Light on the Gateway is SOLID Green. 7. Get the Yellow Cable 8. Plug one end of the Yellow Cable into any of the Yellow Ports on the back of the Wireless DSL Gateway. 9. Make sure that your computer is turned on. Then, plug the other end of the Yellow Cable into the Ethernet Port on the back of the computer. An Ethernet Port looks similar to a regular Phone Jack, but is slightly larger. 10. Make sure that 1 of the 4 Ethernet lights on the Gateway is Green. This may take a few moments. 11. Get the Black or Green DSL Cable from your DSL Quick Start Kit. (Note: two DSL cables if using T2200H) 12. Plug one end of the DSL Cable into the Grey Port located on the back of the Gateway. (Note: Plug two DSL cables to the Grey Ports on the back of the Gateway) 13. Plug the other end of the DSL Cable into the Phone Jack closest to your Computer. 14. Make sure All Devices with the same phone number as your DSL Line has Phone Filters. This includes telephones, fax machines, caller ID boxes, satellite TV receivers, TiVo devices, and answering machines. 15. Make sure that that Power and DSL Lights are solid Green. This may take up to 30 seconds. Note: If the DSL Light continues to blink, make sure you received notification from your DSL Internet Service Provider that your DSL service has been activated. ...
- Page 3 Configure the Gateway 1. Open a Web Browser (FireFox or Internet Explorer, for example). In the address bar, enter http://192.168.1.254 then press Enter on the keyboard. Note: When you open your web browser you may get a page cannot be displayed error. This is normal and will not effect the instructions in step 1. 2. The GUI login username and password values can be found on the bottom sticker. 3. The "Main Menu" screen appears. Note: If this screen does not appear, make sure our Ethernet port is configured for Dynamic IP. Configure Wireless Connection and Security 1. Click on Wireless Setup 2. Select a name for your wireless network and enter it in the "Network Name" field. Then click Apply. 3. Click on Wireless Security from the left column menu. 4. Select the type of wireless security that you want to use Actiontec recommends using WPA&WPA2. The following steps will show you how to enable WPA&WPA2 wireless security. Note: All of your other wireless devices will need to support that same type of wireless security chosen in order to connect to your wireless network. 5. Enter in a password or pre‐shared key. The key must be at least 8 characters long. Click Apply to continue. Congratulations you are now connected! ...
- Page 4 Specifications 1. Features • Supports Plug‐and‐Play installation. • Compliant with full‐rate ANSI T1.413 Issue 2 and ITU G.992.1 (G.dmt) standard. • ADSL2+ / VDSL2 Bonded / Single Line Compliant • DMT modulation and demodulation. • Supports RFC1483 (bridged Ethernet over ATM) for LAN mode. • Full‐rate adaptive modem: max. Downstream rate is 8 Mbps, max. upstream rate is 1 Mbps. • Compliant with IEEE 802.3 Ethernet standard. • Supports 10BaseT and 100BaseT and Gigabit. • 2.4 GHz IEEE 802.11n • Supports 20/40 MHz channels with optional SGI • Full IEEE 802.11 b/g/n legacy compatibility with enhanced performance Comprehensive wireless network security support that includes WPA, WPA2, and AES encryption/decryption coupled with TKIP and IEEE 802.1X support • Support 802.11b and Draft STD 802.11g Modulation. • 802.11b Data Rates: 11Mbit/s, 5.5Mbit/s, 2Mbit/s, 1Mbit/s (And 22Mbit/s with PBCC); • 802.11g Data Rates: 6Mbit/s, 9Mbit/s, 12Mbit/s, 18Mbit/s, 24Mbit/s, 36Mbit/s, 48Mbit/s, 54Mbit/s. • 802.11g Data Rates: 65Mbit/s, 130Mbit/s 2. Power requirements •...
- Page 5 FCC_GR&CN_pkginsrt_Canada10_FCC Reg_Comp sheet_10x6 2/7/13 10:08 AM Page 1 General Regulatory and Compliance Notices Important Safety Instructions Modifications If applicable, when using telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electrical The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by shock, and personal injury, including the following: Actiontec Electronics, Inc, may void the user’s authority to operate the equipment.
- Page 6 FCC_GR&CN_pkginsrt_Canada10_FCC Reg_Comp sheet_10x6 2/7/13 10:08 AM Page 2 Avis d’application de la réglementation et de conformité généraux Consignes de sécurité importantes Modifications Afin de réduire les risques d’incendie, de blessures corporelles ou d’électrocution, suivez toujours ces mesures préventives de base Conformément à...