Work Smart DC2990 Instructions De Montage

CHAISE PNEUMATIQUE POUR DESSINATEURS
10
14
5
12
13
11
3
8
1
Enlever toutes les pièces du carton, les organiser selon les numéros de pièce indiqués
sur la liste et vérifier les quantités des pièces.
ÉTAPE 1 Insérer les cinq roulettes (2) dans la base (1). Pousser fermement jusqu'à ce que les roulettes (2) s'encliquettent. Glisser le vérin pneumatique (3) à
travers le repose-pied (8) et dans la base (1), glisser le soufflet (4) sur le vérin pneumatique (3). VOIR LE DÉTAIL A. SERRER COMPLÈTEMENT LE
BOUTON DE REPOSE-PIED.
ÉTAPE 2 Fixer la plaque du siège (5) au coussin du siège (6) avec six vis (9). RESSERRER COMPLÈTEMENT TOUTES LES VIS AVEC
LA CLÉ ALLEN (15).
ÉTAPE 3 Fixer le support du dossier (14) à l'arrière de la plaque du siège (5) avec le grand bouton de réglage (11), une rondelle en étoile (12) et une
rondelle plate (13). Fixer l'assemblage du dossier (7) au support du dossier (14) avec le petit bouton de réglage (10).
ÉTAPE 4 Placer le siège assemblé sur le dessus du vérin pneumatique (3) et pousser vers le bas.
ATTENTION: AVANT D'UTILISER LE FAUTEUIL, S'ASSURER D'AVOIR SERRÉ COMPLÈTEMENT TOUTES LES VIS.
DC2990 / DC2990V
INSTRUCTIONS DE MONTAGE
7
6
DÉTAIL A
9
4
PIÈCE
1. Base . . . . . . . . . . . . . . . . . . . . . . . 1
2. Roulettes . . . . . . . . . . . . . . . . . . . . 5
3. Vérin pneumatique . . . . . . . . . . . . 1
4. Soufflet . . . . . . . . . . . . . . . . . . . . . 1
5. Plaque du Siège . . . . . . . . . . . . . . 1
6. Coussin du Siège . . . . . . . . . . . . . 1
7. Assemblage du dossier. . . . . . . . . 1
8. Repose-pied . . . . . . . . . . . . . . . . . 1
9. Vis . . . . . . . . . . . . . . . . . . . . . . . . . 6
10. Petit Bouton de Réglage . . . . . . . 1
11. Grand Bouton de Réglage. . . . . . 1
12. Rondelle en Étoile. . . . . . . . . . . . 1
13. Rondelle Plate . . . . . . . . . . . . . . . 1
14. Support du Dossier . . . . . . . . . . . 1
2
15. Clé Allen (non montrée) . . . . . . . . 1
© Office Star Products avril 2017
1
2
QTÉ
WORK SMART LIMITED WARRANTY
Work Smart chairs are warranted from the date of purchase against failure due to material and workmanship as follows:
• 15 Years on all non-moving metal parts.
• 5 Years on component parts including Control mechanisms, pneumatic cylinders, wood, plastic parts, base and casters.
• 3 Years on upholstery fabric and foam against wear and deterioration.
• Leather is not warranted against routine scratching and scuffing, as leather is subject to minor blemishes in use.
To make a warranty claim, contact Parts Department. Provide model number, proof of purchase, description of the problem and obtain return authorization.
At it's option Office Star Products will:
(a) Supply compatible components of current manufacture.
(b) Repair the customer's component. The customer must prepay freight on any components returned to the factory. Return freight on components
still in warranty will be paid by Office Star Products.
*All warranties are limited to the original purchaser for normal commercial usage defined as a standard forty hour work week by persons weighing 250 lbs. or
less. The BC9601 is for persons weighing 300 lbs. or less. The BC9602 is for persons weighing 400 lbs. or less. The BC9603 is for persons weighing 500 lbs.
or less. EX1098, EC1283C & ECH12801 are for persons weighing 350 lbs. or less. This warranty will not cover labor, freight or damage from misuse, abuse,
negligence, alteration, accident, vandalism, rusting, acts of nature or any other event beyond the control of Office Star Products. The warranty does not cover
cosmetic damage that may result from normal use. Liability for incidental or consequential damages is excluded. The user assumes all risk of injury resulting
from use of this product. When usage is more than 40 hours per week, a two year warranty on all parts applies. Fabric is warranted for one year. This warranty
gives you specific legal rights, and you may also have other rights which vary from state to state.
All Work Smart chairs are built to meet or exceed ANSI BIFMA standards.
It is the customer's responsibility to prepay freight on any components returned to the factory. Return freight on components covered by warranty
will be paid by Office Star Products.
Our quality standards are among the highest in the industry. Sometimes, no matter how hard we try, there are times when parts are damaged or missing. Our
Parts Department will do everything possible to promptly remedy the problem. Contact us via e-mail parts@officestar.net, by Fax 1-909-930-5629, or toll free
parts number 1-800-950-7262, Monday through Friday 8:00 a.m. - 5:00 p.m. Pacific Time.
DC2990 / DC2990V
PNEUMATIC DRAFTING CHAIR
OPERATING INSTRUCTIONS
FEATURES
• PNEUMATIC SEAT HEIGHT ADJUSTMENT
To raise seat remove pressure from seat and lift lever (1) up. To
lower seat height sit on chair and lift lever (1) up.
NOTE: It is normal for chair to slightly lower under
body weight.
• FOOTRING HEIGHT ADJUSTMENT
To adjust footring height, loosen knob (2) adjust footring to
desired height, and tighten knob (2) completely to secure
footring into position.
WARNING
1. Use this product only one person at a time.
2. Do not use this chair unless all bolts screws and
knobs are securely tightened.
3. Check that all bolts screws and knobs are tight every
three months or as needed.
4. Dispose of packing material properly. Do not use
plastic cover as head covering. It may cause
suffocation.
5. Do not use chair as a stepladder.
6. Use this chair for its intended purpose only.
7. Use mild detergent only for cleaning.