Office Star Products Space Seating 5500 Instructions De Montage

FAUTEUIL DE DIRECTEURS PROFESSIONNEL AU
ÉTAPE 1 ÉTAPE 2
13
8
2 x5
9
1
ÉTAPE 4 ÉTAPE 5
13
10 x3
4
12
3
6
1
Enlever toutes les pièces du carton, les organiser selon les numéros de pièce indiqués sur la liste et vous assurer que
les quantités des pièces sont correctes.
ÉTAPE 1 Insérer cinq roulettes (2) dans la base (1), les pousser très fort jusqu'à ce que vous entendiez ou sentiez la roulette (2) s'enclencher.
ÉTAPE 2 Aligner les trous des accoudoirs (7L et 7R) sur les trous du coussin du siège (5), fixer les accoudoirs (7L et 7R) au coussin du siège (5) avec
trois vis des accoudoirs (8) et trois rondelles plates (9) pour chaque accoudoir. RESSERRER COMPLÈTEMENT TOUTES LES VIS DES
ACCOUDOIRS (8) AVEC LA CLÉ ALLEN (13).
ÉTAPE 3 Fixer la plaque du siège (4) au coussin du siège (5) avec la flèche vers l'avant du siège avec quatre vis pour plaque du siège (11). RESSERRER
COMPLÈTEMENT TOUTES LES VIS DE LA PLAQUE DU SIÈGE (11) AVEC LA CLÉ ALLEN (13).
ÉTAPE 4 Fixer le support du dossier (12) à l'arrière du plaque du siège (4) avec trois vis du support de dossier (10).
RESSERRER COMPLÈTEMENT TOUTES LES VIS DU SUPPORT DU DOSSIER (10) AVEC LA CLÉ ALLEN (13).
ÉTAPE 5 Insérer le cylindre pneumatique (3) dans la base (1). Placer le siège assemblé sur le cylindre pneumatique (3) et mettre de la pression vers le bas.
ATTENTION : AVANT D'UTILISER LE FAUTEUIL, VOUS ASSURER D'AVOIR RESSERRÉ COMPLÈTEMENT
TOUTES LES VIS.
5500 / 5500D / 5520 / 5560 / 5700
DOSSIER À MAILLES AÉRÉES
INSTRUCTIONS DE MONTAGE
ÉTAPE 3
13
x3
8
11
x3
x3
9
x3
4
7L
5
7R
PIÈCE
1. Base . . . . . . . . . . . . . . . . . . . . . . . 1
2. Roulettes . . . . . . . . . . . . . . . . . . . . 5
3. Vérin pneumatique . . . . . . . . . . . . 1
4. Plaque du siège . . . . . . . . . . . . . . . 1
5. Coussin du siège . . . . . . . . . . . . . . 1
6. Assemblage du dossier . . . . . . . . . 1
7. Accoudoirs (7L et 7R) . . . . . . . . . . 2
8. Vis des accoudoirs . . . . . . . . . . . . 6
9. Rondelles plates . . . . . . . . . . . . . . 6
10. Vis du support du dossier . . . . . . 3
11. Vis de la plaque du sièges . . . . . . 4
12. Support du dossier (préinstallé) . . 1
13. Clé Allen . . . . . . . . . . . . . . . . . . . 1
x4
3
5
1
QTÉ
SPACE LIMITED WARRANTY
SPACE® chairs are warranted* from the date of purchase against failure due to material and workmanship as follows:
• Lifetime on component parts including pneumatic cylinder, control mechanism, base and casters.
• 3 Years on upholstery fabric and foam against wear and deterioration.
• Leather is not warranted against routine scratching and scuffing, as leather is subject to minor blemishes in use.
To make a warranty claim, contact Parts Department. Provide model number, proof of purchase, description of the problem and obtain return authorization.
At it's option Office Star Products will:
(a) Supply compatible components of current manufacture.
(b) Repair the customer's component. The customer must prepay freight on any components returned to the factory. Return freight on components
still in warranty will be paid by Office Star Products.
*All warranties are limited to the original purchaser for normal commercial usage defined as a standard forty hour work week by persons weighing 275 lbs. or less. The
63-37A773HM, 75-7A773, 75-37A773, 75-47A773 and 839-11B35WA are for persons weighing 400 lbs. or less, the 818 & select 829's with self-adjusting mechanism are
300 lbs. or less and the 15-37A720D is 325 lbs. or less. This warranty will not cover labor, freight or damage from misuse, abuse, negligence, alteration, accident, vandalism,
rusting, acts of nature or any other event beyond the control of Office Star Products. The warranty does not cover cosmetic damage that may result from normal use. Liability for
incidental or consequential damages is excluded. The user assumes all risk of injury resulting from use of this product. When usage is more than 40 hours per week, a five year
warranty on all parts applies. Fabric is warranted for one year. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
All Space chairs meet or exceed ANSI BIFMA standards.
Our quality standards are among the highest in the industry. Sometimes, no matter how hard we try, there are times when parts are damaged or missing. Our Parts Department
will do everything possible to promptly remedy the problem. Contact us via e-mail parts@officestar.net, by Fax 1-909-930-5629, or toll free parts number 1-800-950-7262,
Monday through Friday 8:00 a.m. - 5:00 p.m. Pacific Time.
© Office Star Products octobre 2020
5500 / 5500D / 5520 / 5560 / 5700
AIR GRID BACK PROFESSIONAL MANAGER'S CHAIR
OPERATING INSTRUCTIONS
(5500 shown)
FEATURES
• PNEUMATIC SEAT HEIGHT ADJUSTMENT
To raise seat remove pressure from seat and lift lever (1) up. To
lower seat height sit on chair and lift lever (1) up.
NOTE: It is normal for chair to slightly lower under body weight.
• 2-TO-1 SYNCHRO TILT ADJUSTMENT
For individual comfort, this chair has been equipped with an
adjustment that will allow the user to change the tension of the
tilting feature. Turn knob (2) clockwise to increase tension and
counter-clockwise to decrease or ease the tension. To lock return
chair to the upright position, push lever (1) in. To unlock pull lever
(1) out.
NOTE: Be careful not to loosen back tilt adjustment knob completely.
• ARM HEIGHT ADJUSTMENT
To adjust arm height, push button (3) in to allow the arms to
move up or down freely. Release the button (3) once the desired
height is reached.
2
WARNING
1 . Use this product only one person at a time .
2 . Do not use this chair unless all bolts screws and knobs
are securely tightened .
3 . Check that all bolts screws and knobs are tight every three
months or as needed .
4 . Do not overturn back tilt knob when decreasing tension .
5 . Dispose of packing material properly . Do not use plastic
cover as head covering . It may cause suffocation .
6 . Do not use chair as a stepladder .
7 . Use this chair for its intended purpose only .
8 . Use mild detergent only for cleaning .