Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
AM-1 Series™
TEMPERATURE GAUGE ADAPTER
SPECIFICATIONS
Media Temperature Range: 70°F-180°F (21°C-49°C)
Lead Free Plumbing Code Compliance: The wettable
surfaces contain less than .25% of lead by weighted
average
Operating Pressure: 150 psi (1034 kPa) maximum.
Temperature Gauge Adapter: Lead-free brass, EPDM
o-ring, VR90 Gasket
Union Sweat Fitting
Gauge adaptor fits AM-1 series mixing valves.
Gauge dial is 2"and 2.5" diameter.
Installation of Temperature Gauge
Adapter
IMPORTANT
Union sweat connections must be soldered before
the thermowell with O-ring and sealing gasket are
installed. Install the thermowell with O-ring and
sealing gasket after the joint has cooled.
By using this Honeywell literature, you agree that Honeywell will have no liability for any damages arising out of your use or
modification to, the literature. You will defend and indemnify Honeywell, its affiliates and subsidiaries, from and against any
liability, cost, or damages, including attorneys' fees, arising out of, or resulting from, any modification to the literature by you.
Home and Building Technologies
In the U.S.:
Honeywell
1985 Douglas Drive North
Golden Valley, MN 55422
customer.honeywell.com
1. Install thermowell with O-ring to the thermometer
adapter body.
2. Tighten to 75 LB-IN ± 10 LB-IN. DO NOT OVER-
TIGHTEN.
3. Install the thermometer into the thermowell until
seated and tighten the set screw to secure in place.
SCREW
Part No.
AM1-TG100-US-LF/U
AM1-TG101-US-LF/U
AM1-TG102-US-LF/U
TG200-UT/U
TG250-UT/U
® U.S. Registered Trademark
© 2017 Honeywell International Inc.
38-00061EFS—01 M.S. 01-17
Printed in United States
INSTALLATION INSTRUCTIONS
Fig. 1. Temperature gauge installation.
Table 1. AM-1 Series Replacement Kits.
1/2" AM1 Temp Gauge Tail PC w/Sweat
3/4" AM1 Temp Gauge Tail PC w/Sweat
1" AM1 Temp Gauge Tail PC w/Sweat
Thermometer, 2" Dial w/ Threaded Well
Thermometer, 2.5" Dial w/ Threaded Well
THERMOMETER
THERMOWELL
O-RING
THERMOMETER
ADAPTER WITH
UNION NUT
GASKET
M36644
Description
38-00061EFS-01
Publicité
Manuels Connexes pour Honeywell AM-1 Serie
Sommaire des Matières pour Honeywell AM-1 Serie
- Page 1 By using this Honeywell literature, you agree that Honeywell will have no liability for any damages arising out of your use or modification to, the literature. You will defend and indemnify Honeywell, its affiliates and subsidiaries, from and against any liability, cost, or damages, including attorneys’...
- Page 2 Vous défendrez et indemniserez Honeywell, ses sociétés affiliées, filiales pour et contre toute responsabilité, frais ou dommages, y compris les honoraires d'avocats, résultant de quelque manière, ou survenant en connexion avec toute modification à la documentation de votre part.
- Page 3 Serie AM-1™ TERMÓMETRO CON ADAPTOR INSTRUCCIONES DE INSTALACIÓN 1. Instale el termopozo con junta tórica en el cuerpo del adaptador de termómetro. 2. Ajústelo a 75 LB-IN ± 10 LB-IN. NO LO AJUSTE DE MÁS. 3. Instale el termómetro en el termopozo de forma que se asiente de manera adecuada y ajuste el tornillo empotrado para asegurarlo.
- Page 4 Con la utilización de la presente documentación, usted acepta que Honeywell no tendrá responsabilidad alguna por los daños que pudieren surgir del uso o la modificación que usted haga de la documentación. Usted exime a Honeywell, sus afiliadas y subsidiarias de toda responsabilidad, costos o daños, incluyendo las tarifas de abogados, que pudieren surgir o resultar de cualquier modificación que usted realice a esta documentación.