Publicité

Les langues disponibles

Les langues disponibles

Liens rapides

AVX-P7300DVD
This product conforms to CEMA cord colors.
Le code de couleur des câbles utilisé pour ce produit est
conforme à CEMA.
Printed in Japan
Imprimé au Japon
<CRD3479-A> UC
<KYMFF/01D00000>
Connecting the Units
Note:
• This unit is for vehicles with a 12-volt battery and
• To prevent incorrect connection, the input side of
negative grounding. Before installing it in a recre-
the IP-BUS connector is blue, and the output side
ational vehicle, truck, or bus, check the battery
is black. Connect the connectors of the same
voltage.
colors correctly.
• To avoid shorts in the electrical system, be sure to
• If this unit is installed in a vehicle that does not
disconnect the ≠ battery cable before beginning
have an ACC (accessory) position on the ignition
installation.
switch, the red lead of the unit should be connected
• Refer to the owner's manual for details on
to a terminal coupled with ignition switch ON/OFF
connecting the power amp and other units, then
operations. If this is not done, the vehicle battery
may be drained when you are away from the vehi-
make connections correctly.
cle for several hours. (Fig.1)
• Secure the wiring with cable clamps or adhesive
tape. To protect the wiring, wrap adhesive tape
around them where they lie against metal parts.
• Route and secure all wiring so it cannot touch any
moving parts, such as the gear shift, handbrake and
seat rails. Do not route wiring in places that get
hot, such as near the heater outlet. If the insulation
of the wiring melts or gets torn, there is a danger of
the wiring short-circuiting to the vehicle body.
ACC position
No ACC position
• Don't pass the yellow lead through a hole into the
engine compartment to connect to the battery. This
will damage the lead insulation and cause a very
dangerous short.
• Do not shorten any leads. If you do, the protection
circuit may fail to work when it should.
• Never feed power to other equipment by cutting
• Cords for this product and those for other products
the insulation of the power supply lead of the unit
may be different colors even if they have the same
and tapping into the lead. The current capacity of
function. When connecting this product to another
the lead will be exceeded, causing overheating.
product, refer to the supplied Installation manuals
• When replacing fuse, be sure to use only fuse of
of both products and connect cords that have the
the rating prescribed on the fuse holder.
same function.
• If the RCA pin jack on the unit will not be used, do
not remove the caps attached to the end of the con-
nector.
When Connecting the Multi-Channel AV Master Unit
Multi-Channel AV
Master Unit (e.g. AVM-P9000R)
(sold separately)
Green
Red (Right)
White (Left)
Yellow
Blue
Yellow
Fig. 1
Blue
Red
IP-BUS cable
(supplied with the TV tuner)
FM MODULATOR
IP-BUS MAIN UNIT
IP-BUS AV MASTER
RCA cable
(sold separately)
Red
20 pin cable
(supplied with the TV tuner)
Gray
Connection box
RGB cable
(supplied with the DVD
(supplied with the Multi-
Navigation Unit)
Channel AV Master Unit)
Red
Green
To video output
To audio outputs
RCA cables (sold separately)
Yellow/black
To Yellow/black lead (GUIDE ON)
on the navigation unit.
Optical cable
(supplied with the Multi-
Channel AV Master Unit)
Black
Blue
Hide-away TV Tuner
(e.g. GEX-P7000TV)
RCA cable (supplied)
(sold separately)
6 m
IP-BUS cable (supplied with the
Green
Multi-Channel AV Master Unit)
AV cable
(supplied with the
Multi-Channel AV
Gray
Green
Master Unit)
<ENGLISH>
DVD Navigation Unit
(e.g. AVIC-9DVD)
(sold separately)
Voice guidance speaker
(supplied)
Multi-CD player
(sold separately)
3 m
Blue
This product
40 cm
Black
Not used.
Blue
40 cm
16 cm
Yellow
(AVM OUTPUT)
20 pin cable
Red
3 m
(supplied)
Fig. 2

Publicité

Table des Matières
loading

Sommaire des Matières pour Pioneer AVX-P7300DVD

  • Page 1 Green (sold separately) AVX-P7300DVD cle for several hours. (Fig.1) • Secure the wiring with cable clamps or adhesive Red (Right) tape. To protect the wiring, wrap adhesive tape To video output around them where they lie against metal parts.
  • Page 2: Connecting The Units

    Connecting the Units <ENGLISH> When Using a Display Connected Rear Video Output When Connecting the Head Unit Connecting the Power Cord This product’s rear video output is for connection of a display to enable passengers in the rear seats to watch the DVD or Video CD. Connection method Connection box WARNING...
  • Page 3: Din Front/Rear-Mount

    Installation <ENGLISH> 7 When the installation space is not very deep Note: DIN Rear-mount 2. Install side brackets. (Fig. 8) • Before finally installing the unit, connect the • If installation angle exceeds 30° from horizontal, When installing in a shallow space, secure with side brackets (small). In this case, stick con- wiring temporarily, making sure it is all connected the unit might not give its optimum performance.
  • Page 4 Installation <ENGLISH> 2. Fastening the unit to the factory radio mounting bracket. Installing the Voice Guidance Speaker (Fig. 12) (Fig. 13) Precaution: Select a position where the screw holes of the bracket and the screw holes of this product • Do not install on the dashboard where it may be subjected to direct sunlight. High temperatures may result in damage to the unit.
  • Page 5: Raccordements Des Appareils

    Raccordements des appareils <FRANÇAIS> Remarque: Lors du raccordement à l’usnité maîtresse audiovisuel multicanaux • Cet appareil est destiné aux véhicules avec une • Pour éviter une connexion incorrecte, le côté entrée batterie de 12 V, avec pôle négatif à la masse. du connecteur IP-BUS est bleu et même couleur Unité...
  • Page 6: Branchement Du Cordon D'alimentation

    Raccordements des appareils <FRANÇAIS> Lors de l’utilisation d’un écran raccordé à la sortie vidéo arrière Branchement du cordon d’alimentation Lors du raccordement à l’élément central La sortie vidéo arrière de cet appareil est destinée à un écran placé de telle sorte que les passagers arrière puissent regarder les images fournies par un DVD ou un Video CD.
  • Page 7: Montage Din Avant/Arrière

    Installation <FRANÇAIS> 7 Lors de l’installation dans une cavité peu profonde Remarque: 2. Installez les supports latéraux. (Fig. 8) Montage DIN arrière • Avant de finaliser l’installation de l’appareil, • L’angle de l’installation, ne doit pas dépasser 30° Lors de l’installation dans une cavité peu profonde, fixez avec les supports latéraux (petits). connecter temporairement le câblage en s’assurant par rapport à...
  • Page 8: Installation Du Haut-Parleur De Guide Vocal

    Installation <FRANÇAIS> 2. Fixation de l’appareil au support de montage d’autoradio pourvu par l’usine. Installation du haut-parleur de guide vocal (Fig. 12) (Fig. 13) Précaution: Choisissez une position telle que les perçages de vis du support soient en regard (face à face) •...

Table des Matières