Honeywell FocusPRO 6000 Serie Information Produit

Programmable
Digital
Thermostat
Product
Information
Thermostat controls
Function buttons
Press to select the function displayed just above each
button. (Functions change depending on the task.)
Display screen
Low battery Auxiliary heat (Only
warning for heat pumps with
auxiliary heat)
Current inside
temperature
Inside
72
Press the SET
button to change:
Clock:
Current time.
Wake
Day:
Current day.
Schedule:
Current
Set Clock/Day/
thermostat program
Schedule
schedule.
Press the FAN
button to select:
Function buttons
Auto:
Fan runs only
Press the button beneath each
when heating or cooling
function to view or change
system is on.
settings (functions change
On:
Fan runs continuously.
depending on the task)
Program Schedule
You can program four time periods each day, with different settings for
weekdays and weekends. We recommend the pre-set settings (shown in
the table below), since they can reduce your heating/cooling expenses.
Wake - Set to the time you awaken
and the temperature you want during
the morning, until you leave for the
day.
Leave - Set to the time you leave
home and the temperature you
want while you are away (usually an
energy-saving level).
Return - Set to the time you return
home and the temperature you want
during the evening, until bedtime.
Sleep - Set to the time you go to bed
and the temperature you want overnight (usually an energy-saving level).
NOTE: Leave and Return periods can be canceled on weekends.
Reference card
Battery holder
Hold Button
Press to override programmed
temperature control
Temperature buttons
Press to set preferred temperature.
Digital display
Temperature
setting
System Status
Cool On: Cooling
system is on.
Heat
Replace Battery
Setting
72 Heat On: Heating
system is on.
In Recovery
6 : 30
AM
Auxiliary
Press the SYSTEM
Wed
Heat On
button to select:
Fan System
Heat:
Heating system
Auto Heat
control.
Cool:
Cooling system
control.
Off:
All systems off.
MCR29458
Auto:
Thermostat
automatically selects
heating or cooling
depending on the
indoor temperature.
Em Heat:
& Auxiliary Heat
control. Compressor
is locked out. (Select
models only.)
Heat
°
Wake 70
(6:00 am)
°
Leave 62
(8:00 am)
°
Return 70
(6:00 pm)
°
Sleep
62
(10:00 pm)
FocusPRO
6000
To adjust program schedules
Fan
Set Clock/Day/ Auto
Schedule
Done
Set Day
Set Schedule
8 : 00
Leave Mon Tue Wed Thu Fri
Done
CancelPeriod
NOTE: Make sure the thermostat is set to the system you want to
program (Heat or Cool).
NOTE: You can press CANCEL PERIOD to eliminate unwanted time periods
(except Wake).
Program schedule override (temporary)
Inside
69
Run Schedule
want to turn up the heat early in the morning, it will automatically be
Emergency
lowered later, when you leave for the day.
To cancel the temporary setting at any time, press RUN SCHEDULE.
NOTE: Make sure the thermostat is set to the system you want to control
(heat, cool or auto).
Product Manuals
Cool
°
75
Search online for Honeywell 69-1921EFS for the User's Guide.
°
83
°
CAUTION
75
Equipment damage hazard
To prevent possible compressor damage, do not operate
°
78
cooling system when outdoor temperature is below 50°F
(10°C).
Series
1. Press SET CLOCK/DAY/SCHEDULE, then
System
Cool SET SCHEDULE.
2. Press
s
Wake time (Mon–Fri), then press
NEXT.
3. Press
s
Set Schedule
for this time period, then press NEXT.
4. Set time and temperature for the
next time period (Leave). Repeat
Heat
steps 2 and 3 for each weekday time
Setting
62
period.
AM
5. Press NEXT to set weekend time
periods (Sat-Sun), then press DONE
to save & exit.
Next
MCR29462
Press
Heat
Temporary
Setting
adjust the temperature. This
75
will temporarily override the
6 : 30
temperature setting for the
AM
current time period.
Fan System
The new temperature will be
Auto Heat
maintained only until the
next programmed time period
MCR29463 begins. For example, if you
or to set your weekday
t
or to set the temperature
t
or to immediately
s t
33-00303EFS-01