Husqvarna K650 ACTIVE II EPA Manuel D'utilisation
  1. Manuels
  2. Marques
  3. Husqvarna Manuels
  4. Cisailles
  5. K650 ACTIVE II EPA
  6. Manuel d'utilisation
Husqvarna K650 ACTIVE II EPA Manuel D'utilisation

Husqvarna K650 ACTIVE II EPA Manuel D'utilisation

Masquer les pouces
Table des Matières

Publicité

Liens rapides

Télécharger ce manuel
All manuals and user guides at all-guides.com
Eng
F
Esp
K650 ACTIVE II EPA
K700 ACTIVE II EPA
Operator's manual
Read these instructions carefully and make sure you
understand them before using the machine.
Manuel d'utilisation
Lire attentivement et bien assimiler le manuel d'utilisation
avant de se servir de la machine.
Manual de
instrucciones
Antes de utilizar la máquina, lea bien el manual de
instrucciones hasta comprender su contenido.

Publicité

Table des Matières
loading

Manuels Connexes pour Husqvarna K650 ACTIVE II EPA

Sommaire des Matières pour Husqvarna K650 ACTIVE II EPA

  • Page 1 All manuals and user guides at all-guides.com K650 ACTIVE II EPA K700 ACTIVE II EPA Operator’s manual Read these instructions carefully and make sure you understand them before using the machine. Manuel d’utilisation Lire attentivement et bien assimiler le manuel d’utilisation avant de se servir de la machine.

  • Page 2: Table Des Matières

    All manuals and user guides at all-guides.com Contents Replacing the starter cord ......16-17 Foreword ............... 1 Replacing the starter spring ........ 18 Symbols in the operating instructions ....2 Air filter ............19-20 Symbols on the power cutter ........ 3 Carburettor .............

  • Page 3: Foreword

    All manuals and user guides at all-guides.com Foreword The power cutter is a machine with a high cutting capacity and it is fitted with safety features to make the work carried out as safe as possible. If the safety WARNING! features are out of operation or if the machine is used Use only cutting wheels approved for use with carelessly or wrongly, the result can be injuries...

  • Page 4: Symbols In The Operating Instructions

    All manuals and user guides at all-guides.com Symbols in the operating instructions WARNING! This power cutter can be Study the operating instructions carefully dangerous. and make sure that you understand the Careless or incorrect use of this machine can contents before using the power cutter. result in serious, even fatal, injuries.

  • Page 5: Symbols On The Power Cutter

    All manuals and user guides at all-guides.com Symbols on the power cutter WARNING! The power cutter can be Warning dangerous! Careless and incorrect use can Cutting creates a lots of dust which result in serious, even fatal injury. can cause inhalation damages. Use appropriate dust mask or respirator protection.

  • Page 6: Operator Safety Precautions

    All manuals and user guides at all-guides.com Operator Safety Precautions 1. Never operate the machine when you are 5. Never start cutting until you have a clear work area tired, angry, emotionally disturbed, or under the and secure footing. influence of alcohol, drugs, medication, or 6.
  • Page 7 All manuals and user guides at all-guides.com 11. Never operate a cutting machine that is damaged, 17. Operate the machine only in well-ventilated areas. improperly adjusted, or not completely and Failure to use the power cutter in a well-ventilated securely assembled. Be sure that the wheel stops area can lead to serious injury or death.

  • Page 8: Identification

    All manuals and user guides at all-guides.com Identification Identification Denominacion...
  • Page 9 All manuals and user guides at all-guides.com Pos. Description 1. Cutter disc 11. Cover for air filter 2. Guard 12. Air filter 3. Knob for guard adjustment 13. Spark plug (under cover) 4. Stop switch 14. Decompression valve 5. Choke 15.

  • Page 10: Reversing The Cutting Arm

    All manuals and user guides at all-guides.com Reversing the cutting arm It is possible to reverse the cutting arm 180 Turn the arm 180 and then refit parts and screw that the cutter wheel is positioned on the into position as earlier. Note that the flange opposite side of the arm.

  • Page 11: Disque Découpeur

    All manuals and user guides at all-guides.com Cutting wheel The cutting wheel is tightened with the fixed The wheel is placed between the flange washer wrench 501 69 17-02, that is delivered with the A and B. Check the arbor bushing so that it corresponds with the size of the hole in the power cutter.
  • Page 12 All manuals and user guides at all-guides.com The spindle is secured by means of pin WARNING! 503 24 06-02, which is pushed in as far as Never operate without the wheel guard. possible. The wheel is tightened clockwise. The guard should be adjusted so that its rear section is close to the workpiece.

  • Page 13: Drive Belt

    All manuals and user guides at all-guides.com Drive belt The belt is completely enclosed and well Adjust the tensioning screw so that the nut is protected from dust and dirt as well as from positioned at the arrow marked on the cover. mechanical damage during cutting work.

  • Page 14: Fuel Filter

    All manuals and user guides at all-guides.com Fuel filter To replace the belt loosen the two nuts and then Wipe the area around the fuel cap clean before the tensioning screw until the tension is released. the filler cap is removed. Dirt in the fuel tank will Remove the nuts and the belt cover.

  • Page 15: Fuel Mixture

    All manuals and user guides at all-guides.com Gasoline 2%(1:50) Lit. Lit. 0,10 0,20 0,30 0,40 gallon fl. oz. 2 1/2 2 1/2 6 1/2 12 7/8 WARNING! • Use a Partner fuel can with overfilling Fuel mixture protection. • Petrol and petrol fumes are extremely IMPORTANT! The engine is lubricated by the flammable.

  • Page 16: Mandos

    All manuals and user guides at all-guides.com Controls catch. Release the throttle control and the A Stop switch. When the button is pressed throttle is blocked in half throttle position. The backwards, the engine stops. The button remains in this position and must be returned catch is released when the throttle control is pressed in all the way.

  • Page 17: Starting The Engine

    All manuals and user guides at all-guides.com Starting the engine WARNING! Make sure the stop switch (A) is in running The cutting wheel will start to rotate when the position (pushed forward). Pull the choke control saw starts. Make sure that the cutting wheel (B) if the engine is cold.

  • Page 18: Replacing The Starter Cord

    All manuals and user guides at all-guides.com Replacing the starter cord 1. Remove the air filter and cylinder cover. 3. Pull out the starter cord a little and prevent the pulley from rotating backwards. 2. Remove the four screws and lift away the starter.
  • Page 19 All manuals and user guides at all-guides.com 5. Remove the locking spring or screw and lift up 10. Mount the locking spring or screw. the starter pulley. 11. Wind three turns of the starter cord round the 6. Pull the new starter cord through the hole in the pulley.

  • Page 20: Replacing The Starter Spring

    All manuals and user guides at all-guides.com Replacing the starter spring 1. Follow the same procedure as described WARNING! above for replacement of the starter cord. When the recoil spring is assembled in the starter housing, it is in tensioned position and 2.

  • Page 21: Air Filter

    All manuals and user guides at all-guides.com Air filter The filter system consists of a centrifugal cleaning The main filter (2) is removed by means of nozzle (1), main filter (2) and protective filter (3). loosening the two screws which hold the filter The main filter is an oil saturated foam filter and cover.
  • Page 22 All manuals and user guides at all-guides.com Air filter The protective filter (3), which is a paper filter, is When dismantling the cylinder cover it is mounted in the cylinder cover under the filter base. important to check that the seal D is in good This filter must only be shaken clean.

  • Page 23: Carburettor

    All manuals and user guides at all-guides.com Carburettor Jets Governor The carburettor is equipped with fixed jets to The engine is equipped with a carburettor which ensure the engine always receives the correct fuel- has a built-in governor. At the maximum speed, air mixture.
  • Page 24 All manuals and user guides at all-guides.com Idling speed (T) If an adjustment is necessary, adjust with the WARNING! screw marked T on the cover. Adjust the idle Contact your servicing dealer if the idle speed so that the cutter wheel does not rotate. A adjustment cannot be adjusted so that the correctly adjusted idle speed setting (approx.

  • Page 25: Spark Plug

    All manuals and user guides at all-guides.com Spark plug If the engine is low on power, difficult to start or IMPORTANT! runs poorly at idling speed, always check the Always use the recommended spark plug type, spark plug first. If the spark plug is dirty, clean it Champion RCJ-7Y or NGK BPMR 7A.

  • Page 26: Working Technique

    All manuals and user guides at all-guides.com Working technique When cutting stone, concrete and similar mate- When cutting steel and other metals, always try rial the wheel should be moved forwards and to maintain high cutting pressure and high wheel backwards in the cut to obtain good conduction speed.

  • Page 27: Maintenance Scheme

    All manuals and user guides at all-guides.com Maintenance scheme The following is a summary of various measures mentioned in the book and which is essential for the correct servicing of the power cutter. The time intervals mentioned should be applied if the power cutter is used for at least 4 hours every day.

  • Page 28: Outil

    All manuals and user guides at all-guides.com Esquema de mantenimiento A continuación se muestra un sumario de las distintas medidas mencionadas en el libro y las cuales son esenciales para un servicio correcto de la máquina. Los intervalos de tiempo mencionados deberán ser aplicados si la máquina se ha usado por lo menos cuatro horas cada día.

  • Page 29: Technical Data

    All manuals and user guides at all-guides.com Technical data K650 Active K700 Active Engine Air-cooled, two-stroke 71 cm 71 cm Power 3,5 kW 3,5 kW Spark plug Champion RCJ-7Y Champion RCJ-7Y NGK BPMR 7A NGK BPMR 7A Electrode spark gap 0,5 mm (.020") 0,5 mm (.020") Carburetor...

  • Page 30: Données Techniques

    All manuals and user guides at all-guides.com Données techniques K650 Active K700 Active Moteur Refroidi par air, à 2 temps 71 cm 71 cm Puissance 3,5 kW 3,5 kW Bougie Champion RCJ-7Y Champion RCJ-7Y NGK BPMR 7A NGK BPMR 7A Écartement des électrodes 0,5 mm...

  • Page 31: Datos Técnicos

    All manuals and user guides at all-guides.com Datos técnicos K650 Active K700 Active Motor Refrigerador por aire – dos tiempos 71 cm 71 cm Potencia 3,5 kW 3,5 kW Bujía Champion RCJ-7Y Champion RCJ-7Y NGK BPMR 7A NGK BPMR 7A Abertura entre electrodos 0,5 mm...

  • Page 32: Safety Rule Checklist

    All manuals and user guides at all-guides.com Safety rule checklist Operation Operator Before start • Controls work smoothly and correctly. • Is fully instructed in use of the power cutter. • Tank filled min. 3 m (10 feet) away from cutting •...

  • Page 33: Liste De Contrôle, Prescriptions De Sécurité

    All manuals and user guides at all-guides.com Liste de contrôle, prescriptions de Utilisation sécurité Avant la mise en route • Les commandes fonctionnent sans remarque. L’utilisateur devra • avoir appris comment utiliser la découpeuse • Le réservoir de carburant est rempli au moins à 3 mètres du lieu de travail.

  • Page 34: Filtro De Aire

    All manuals and user guides at all-guides.com Lista de chequeo de seguridad Funcionamiento Usuario Antes del arranque • Controlar que los mandos se accionan con facilidad • Ha sido instruido en el manejo de la máquina. y correctamente. • Ha léido y comprendido este manual de seguridad y •...

  • Page 35: Federal Emission Control Warranty Statement

    All manuals and user guides at all-guides.com FEDERAL EMISSION CONTROL WARRANTY STATEMENT YOUR WARRANTY RIGHTS AND WHAT IS COVERED OBLIGATIONS REPAIR OR REPLACEMENT OF PARTS Repair or replacement of any warranted part will be perfor- The EPA (The US Environmental Protection Agency) and med at no charge to the owner at an approved Partner Partner Industrial are pleased to explain the emissions Industrial servicing dealer.
  • Page 36 All manuals and user guides at all-guides.com 108 87 68-79 ´*xlw¶9k¨ 1998W50...

Ce manuel est également adapté pour:

K700 active ii epa

Table des Matières